Specialists of customer support "Tricolor"TV "is most often asked by the question, that there is no reception of TV and radio channels, and" No access "," Coded channel "," Error 0 "or" No signal "appear on the TV.
What should I do if this message appears on the TV screen?
Most often, the error "0" appears whenAccess to viewing channels disappears. This is usually due to the failure of the receiver program. The reasons can be many, up to the voltage drop in the power grid.
In any case, if an error "0" occurs on"Tricolor TV", what to do - experts advise. First of all, for some time, turn off the receiver from the power supply. Then turn on again. This procedure takes about five minutes. When using a conditional access module, you need to remove it, and then put it back into the receiver.
Very often, instead of the error message "0" information is displayed in the form of "Coded channel DRE". At the same time, broadcasting is impossible to watch.
So what does the error "0" mean on "Tricolor TV"?The answer should be sought in the causes of problems. There are universal ways to solve this problem, which are suitable for all types of receivers, which are used to receive channels provided by Tricolor TV. They can be used when the channels are not displayed, but the Infokanal is also running.
If the error "0" is found on "Tricolor TV", how to fix it yourself?
First you need to check whether thesuddenly subscribe to the package services. This is done in your account on the official website or in the menu of the receiver itself. If the subscription has expired, it may well cause a similar error.
Possibly improperly installed in receivercard access, so you need to check the correctness of its installation in the corresponding slot of the receiver. If a conditional access module is used instead of a card, then the check should be made in it.
If the card is inserted correctly, when you press the No. ID button on the remote control, a message will be displayed on the TV screen displaying its number.
Also, when an error occurs, it will not be superfluous to try resetting the receiver to factory settings. In other words, zero them.
This operation is quite possible to do.yourself. You need to enter the receiver's menu and go to the "Settings" section. You will need to enter a four-digit code - type four zeros 0000. After that, you need to find the "Factory settings" and select the line "Delete settings", along with the list of channels. There is nothing dangerous in this operation, after rebooting the receiver using autosearch, the channels can be found again. Most often after this error disappears.
If the subscription is completed, and if the channels from the “One” package are not accepted, it is possible to search for free channels. Usually they are at the very bottom of the list.
In a situation when the receiver was turned off for a long time, there may also be a problem with the error "0" as soon as the receiver is turned on. How to fix the error "0" on "Tricolor TV"?
Should not turn off the receiver, but leaving itturned on for eight hours, wait until the error disappears. Most often this happens much earlier, in an hour and a half. But this is only if both the antenna and the receiver are in good condition.
If you get the error "0" on "Tricolor TV", thatto do if the cause of the error "0" turned out to be poor quality or low level of the received signal from the satellite? Or the lack of activation keys. In this case, if you just leave the receiver on for a long time, it will not help.
You can either send a request to the support service, or try to fix the antenna yourself.
It must be remembered that when it is expected to activate the receiver, it must be turned on to the first channel - that is, 1ORT, and no other. Regardless of whether it is broadcast or not.
If a conditional access module fails, alsoThis error may occur. To determine the version of the installed software on the receiver, click on the remote control to enter the "Status" menu. You can resume the software yourself, while the repair is better to provide a specialized service center.
In most cases, the error "0" also appears when the satellite receiver is overloaded.
Having dealt with the question of what a "0" error is on the "Tricolor TV", we perform several actions to fix it yourself:
So in what situations this error most often appears.
First, you first need to try to determinewho issued this message - a TV or receiver. You should click on the "Ok" button on the remote control - if the outcome is favorable, the TV Tricolor TV channels should appear on the screen. Otherwise, the message that the channel list is empty (which means the error "0" on TV Tricolor TV) appears.
If the receiver responds normally to a button press, the cause of the error may be hidden:
In principle, there is nothing difficult in setting up.It is only necessary to change the position of the antenna and monitor the TV screen. The antenna should be moved gradually, slowly, literally by centimeter. As soon as an image appears on the channel "Info" - the antenna must be fixed.
If you call showing signal strengtha special scale by pressing twice the red "F1" or "i" button on the remote, at the bottom of the screen there will be a signal strength on the left and its quality on the right. In order for channels to be received stably, it is necessary that the signal level be at least 70%.
There is a situation when some channels are notare displayed, there is a message that there is no signal, while others are shown normally. The reason for this may be that the transponders have changed - the frequencies on which the channels are broadcast. It is necessary to rescan them either in manual or automatic search mode.
You will have to enter the menu and select the item “Search for channels“ Tricolor TV ". Then scan the channels.
An error may also occur in case of failure of the satellite dish converter. Then you have to replace the converter itself.
When the reason is that the coax is damagedcable, then you need to replace the cable. You can repair it, but the signal quality may be worse. The junction of the cable may cause additional interference in receiving channels.
If one of such inscriptions as “Coded channel DRE”, “No access”, “Error" 0 "appears on the screen of the television receiver, then we check the following:
- Activity subscription "TV Tricolor". Error "0" on the second receiver is also checked either through the personal account on the official website, or in the "Personal Account" section of the receiver.
If there is no ID number, then:
In a situation if the ID number is defined and the subscription has not expired, then:
So that the error “0” on “Tricolor TV” does not appear anymore, what should I do if the receiver has switched off after leaving for a long time, for example? We'll have to activate the keys again.
To prevent an error message from appearing, the receiver should sometimes be left connected to the network, for example, at night.