Elastic waterproof grout Ceresit CE 40is a colored mortar mixture intended for finishing joints when laying both ceramic tiles and glass, and natural or artificial stone. The mixture can be used for both internal and external works. Grout Ceresit is used on vertical and horizontal surfaces. Recommended for use on deformable substrates, such as chipboard, particleboard, gypsum board. In addition, it is used on surfaces subject to temperature fluctuations: on heated floors, terraces, outdoor pools, etc. Due to the hydrophobic property and high resistance to fungi and mold, it can be used in rooms with constant humidity (bathroom, shower room, kitchen, etc.).
According to the builders' comments, the seam up to 5 mm wide has the following qualities:
The grout Ceresit is used, as a rule, into seal seams between glass or ceramic facing tiles, as well as for those that arise when laying artificial and natural stone, for example marble. It is possible to use both on vertical and horizontal surfaces inside or outside the premises. Grout for tiles Ceresit is recommended for use in places exposed to water (kitchens, bathrooms, showers, swimming pools). Due to the high hydrophobic properties of the material (aquastatic effect), droplets of water, not being able to penetrate the structure of the material, roll off the surface. The mixture is recommended for use on surfaces subject to deformation: particle board, gypsum board or on the heated floor.
It is not allowed to begin grouting joints beforethe end of solidification of the tile adhesive, on which the lining is laid. The seams and end parts of the tiles before the grouting process are cleaned of glue, dirt, dust and other substances that can reduce the adhesion of the trowelling mixture.
The dry grout Ceresit is dissolved with water fromtemperature + 16-28 ° C. For a kilogram of the mixture, add 300-320 milliliters of water, then stir. After obtaining a uniform composition, wait 5 minutes and mix again. The consumption of the dry mix is from 400 to 700 grams per square meter of the lining.
Recommended air temperature duringworks +20 ° C. After 15 minutes after grouting the excess mixture is removed slightly moistened sponge. The dried up grout can be removed with a dry soft cloth. If the temperature deviates from the recommended setting and setting time, the grout may change.
According to feedback, negatively on the operationalThe quality of the joint can be affected by their abundant water rinsing. In the case of excessively intense mashing on its surface, roughness can occur.
Failure to comply with the proportion of water and grout in the preparation of the mixture, as well as the effect of moisture on the base, which is covered with tiles, can lead to minor differences in the color of the seam.
During the first 24 hours after laying, fresh seamsmust be protected from atmospheric precipitation, excessive moisture and low (less than +5 ° C) temperature. Full hydrophobicity of the grouting is achieved after 5 days from the end of the work.
Negative exposure to skincover is not marked. If this mixture is accidentally introduced into the eyes, they should be washed with a large volume of water. If irritation occurs, seek medical attention.
The storage time for the trowel is 18months from the date of manufacture, which is indicated on the packaging. Store the material in a dry place, without removing it from the original sealed packaging.
Features of silicone grout, according to reviews, are as follows:
Silicone grout for joints Ceresit CS25It is used as a sealant to impart moisture-repellent properties, and also to avoid the appearance of fungus and mold in joints and joints of facing tiles in shower cabins, latrines, baths, etc.
As evidenced by the feedback of the builders, itis distinguished by high tenacity to materials made of glass, faience, porcelain and enameled surfaces. Thanks to the formula Trio protection provides long-term protection against fungus and mold, and high resistance to ultraviolet allows you to use this sealant, even with external works.
Grout Ceresit silicone does not have adhesion tosuch materials as Teflon, bitumen, polyethylene, rubber, as well as with products that have the property of isolating any oils, solvents, plasticizers. Avoid contact of the sealant with food, mirror surfaces, limestone, marble surfaces and metal products that can be corroded, since the material contains fungicides, and when it hardens, acetic acid is released.
