Drovnitsa own can be made withease, but before that you need to determine the amount of fuel you intend to put into it. Only with the use of high-quality dried fuel can you get a good steam in the bath and the heat that radiates the design for heating the room. In addition, only with dry wood, you can cook shish kebab according to the rules. If you do not wish to fill up the shed with firewood any more, since there is not enough free space in it, you can independently make a drovnitsu. It is important to find such a place for her that there is an opportunity to guarantee fire safety. Thus, the drifter must be located not so close to the residential building.
Drovnitsa, made by own hands, canhave different sizes. The one that has large dimensions, can be located on the street, and one that is to be used every day, can be located in immediate access from the stove or fireplace. This eliminates the need to go out for firewood every time you need to heal the hearth. The described special place for storing a small portion of logs must also comply with the fire safety rules, which indicates the need to give the structure the ability to ventilate. But as for the external drovnitsy, it must be done so that it has a canopy, because the fuel should not get water.
If a drifter is made by hand, thenIt is necessary to adhere to certain recommendations on the design parameters. Thus, if you want to get a dower for temporary storage of fuel, then its capacity should be in the range of 0.5 to 1.5 m2, this is enough for a bath. Whereas if it is supposed to make a drovnitsu for cooking shish kebabs and other dishes, then this indicator may be somewhat smaller, it can be limited to 0.2-0.4 m2. Drovnitsa, made by hand, can also be portable, so that it would be convenient to bring it to the barbecue grill. Its capacity can be 0.3 m2.
If you need to use the space forstorage of fuel when firing a fireplace or a stove, wood or metal can be used as a material for manufacturing. Less often, such drovnitsy are made from willow twigs, but they look very original and harmonious. As the main feature of portable fuel storage is a small weight of the product, in addition, the design should be characterized by an impressive capacity, but do not zealous with the latter quality, because you can get a setup that will take up too much space, and use it as a portable capacity will be uncomfortable.
Drovnitsa own hands at the dacha should beis made in such a way that the bottom is solid, this will prevent the loss of debris and all sorts of wooden remains. If you make a portable drovnitsa, then it must be done with handles. Making a place to store firewood, which is intended to be used only in the house, wheels can be attached to the bottom.
The firewood dvirnitsa can be made by oneself, if it is possible to prepare some materials and tools, among them it is necessary to distinguish:
The amount of building material will depend onfrom the dimensions of the structure. If the drovnitsa is installed on the street, then it is necessary to protect and its side walls, for this you should use a corrugated sheet. However, it is also possible to sew the side walls with a strap.
Drovnitsa own hands at the dacha should beis installed using a special technology, the features of which will be described below. Once you can select the location for installation, you need to prepare four pits, each of which will be mounted post. Depending on what capacity will have a drifter, you need to determine the distance between the supports. Conditionally, we can assume that the length of the storage space should be about 3 meters, while the width should not exceed 1.5 meters. In the role of supports it is necessary to use a paired bar, the cross-section of which is 50 x 50 mm. Pits should be deepened by 40 or 50 cm.
Front and rear supports must have differentlength. This indicates that the lengths of the beam, which will be located behind and in front, should have a length of 2 and 2.3 m, respectively. At the next stage, they must be installed in ready pit, and then covered with stones with clay. Each of the materials is filled up separately, so that it is possible to produce a ramming. It is necessary to protect the buried part of the supports with a special material, which can be used as a sticky tape or roofing material. This will ensure a higher degree of moisture-proof construction.
Strapping mounted poles is necessaryperform using a bar, you need to do this on three levels. The bars, which should be located in the lower part, should be strengthened in steps of 10-15 cm from the construction site. As for the next bar, it must be fixed to the central part of the supports located at the rear. After that, you can proceed to the manufacture of the upper screed, which is mounted on the rear and front posts on their upper ends.
Side supports should be fixed to each other by means of a bar on three levels. A stronger and more stable construction will become if the braces to its rear and side rails are strengthened.
Before you make a douche wood with your own hands,it is necessary to think whether it will have a carcass cladding. In favor of this, we can say that this design will protect the wood from rain. In view of the fact that the pillars have different lengths, the master will have the opportunity to equip the pitched roof. You can take other sizes of poles, but in the example a difference of 30 cm is used. If you provide a slope, this will guarantee that the moisture is draining.
When a douche brewer is made by hand,projects must be prepared in advance. They can be seen in the article. At the next stage of the work, you can start laying the crate, which is mounted on the upper screeds. If there is a desire, then the insulating material can be laid on the roof. As a covering material, slate can be used.
When the street dovnitsa is made byhands, on the ground under the boards should be laid logs, the step between which should be equal to 1 m. This will allow additional ventilation drovnitsy. If the design is installed on a solid surface, then this method should be discarded. The wall covering should not be made deaf, but leave grooves for better ventilation. This is how the drovnitsa is made for the fireplace with their own hands. Projects of this design can be seen in the article, it can easily be performed independently.