If you at least once made repairs, you've heard ofbrand "Found". Among its other products, it is necessary to allocate plaster, which can have a different purpose. The advantage of this product is not only high quality, but also affordable cost, which is provided by its own production facilities.
The company specializes in dry buildingblends since 2005. Used compounds for facade and interior works, they are suitable for finishing walls, partitions and ceilings. With the help of these mixtures it is possible to give the surfaces an impeccable smoothness, while there are no restrictions in the humidity level in the room. It can be:
If you are interested in the products of the company"Found", the cement plaster you can be chosen. Her brand is mentioned in the subheading above. Provides a fairly low flow rate, as well as thermal insulation and soundproofing qualities. The resulting layer differs in weather resistance and vapor permeability. Manual and machine application is allowed, but a mixture for exterior and interior works is suitable.
It is possible to use this plaster forleveling of walls from cellular and ordinary concrete, and also bricks. It is recommended that the composition for the facade, but in this case, the application should be carried out above the socle part. However, this plaster is suitable for rooms, the operating conditions of which can differ by any level of humidity.
The above described plaster "Found" has a graycolor, compressive strength can be greater than or equal to 3 MPa, flexural strength is 1 MPa or more, whereas the adhesion level with the base is equivalent to 0.4 MPa, however this parameter may be higher. The maximum fraction of particles is 2.5 mm, the recommended thickness of the composition layer can vary from 10 to 30 mm. On 1 kg of a dry mix at mixing of structure it is required 0,17-0,21 l of water.
If plaster is applied in one layer, the thickness of which is 10 mm, then 1 m2 it will take approximately 10 kg of plaster.Plaster "Found" after the connection with water will be suitable for work for 3 hours. It is important to know also the coefficient of vapor permeability, which can be equal to or greater than 0.12 mg / m * h * Pa. Specialists who purchase this solution are often interested in the brand of mobility, it looks as follows: PC3.
If it is necessary to apply polymer materialsby the type of putties and paints, these operations can be performed after 14 days. Frost resistance of the created layer will be 35 cycles. The subsequent plaster layers can be applied after 24 hours. Gypsum putty or tile adhesive can be applied after three days. This "Base" plaster can be applied at a substrate temperature and ambient temperature in the range from +5 to +30 ° C. The layer can be used for a wide range of temperatures, which varies from -50 to +65 ° C.
This mixture has a high elasticity, lowflow, is highly resistant to cracking, weather resistance and suitable for walls of cellular and ordinary concrete, as well as bricks. This composition can be said to be universal, characterized by high plasticity of the finished solution and has the quality of vapor permeability.
This plaster facade "Found" hasbending strength within 2 MPa, as to the strength of adhesion to the base, this parameter is 0.4 MPa. On 1 kg of a dry mix approximately 0,15 l of water will leave. If partial alignment is carried out, the recommended layer thickness is 40 mm. When it comes to continuous alignment, this parameter can vary between 5 and 30 mm.
After mixing, the solution retainsviability for two hours. Frost resistance is quite high and reaches 50 cycles. The described plaster "Found" can be operated at a temperature ranging from -50 to +65 ° C.
This composition of gray color is universalplaster, which can be laid with a layer from 3 to 80 mm thick. According to the buyers, the viability of the mixture is optimal, the composition has high vapor permeability, ductility and evenly hardens when applied. Users emphasize that the layer does not require shpaklevaniya, and also suitable for rooms with normal humidity.
Use this gypsum mixture forleveling of surfaces inside premises. If you get acquainted with the feedback of consumers, you will be able to learn that the recommended bases are gas and foam concrete surfaces, plaster, concrete and brick walls. Here you can include walls and ceilings from:
The above-described gypsum plaster "Found"contains particles whose maximum fraction does not exceed 0.63 mm. The bending strength is 1.5 MPa, while the compressive strength is 3 MPa, these parameters may be greater. The adhesion to the base is 0.3 MPa. When closed, 1 kg of dry mixture will take approximately 0.47 liters of water. If the thickness of the layer reaches 10 mm, then the flow rate of the mixture is 1 m2 will be 9 kg. The thickness of the layer should vary from 3 to 80 mm.
After mixing, the composition will remain viable for 1.5 hours.
Plaster "Will Establish Gypsum" can be appliedat ambient temperature and bases in the range from +5 to +30 ° C. As for the temperature during operation, it should not exceed the limits of +5 - +40 ° C. The next layer can be applied at least a day.
Not so long ago in the construction marketmaterials it was possible to find homemade solutions in a wide range. Already today the most popular are the mixtures of factory production. Consumers choose them for the reason that the composition contains mineral components and sand, as well as various modifiers. Modern cement plaster allows to level any irregularities, and the composition can be used for manual or machine application.
