Почти каждый строитель, который сталкивался с the question of the construction of buildings for any purpose, wondered how to make a goat building with his own hands. Without them, it will be rather difficult to carry out the mentioned manipulations. The design can be rented, but it is quite expensive, which is especially true of the case, which involves building construction for a long time.
If goats building their own hands willto be made, then you first need to prepare all the materials and tools. Among the former one can distinguish a pipe whose diameter can be equal to 1.5 or 2 inches. The final parameter depends on the expected loads. You will need a pipe with a diameter of 1 and 1.5 inches, the figure will depend on the parameter of the pipe, which was described above. From blanks to perform horizontal jumpers that will connect the rack. Another pipe with a diameter of 0.5 inches will be necessary for the manufacture of hooks, which are installed horizontally oriented jumper. A round rod with a diameter of 14 millimeters will act as pins. This blank is to be welded onto a horizontal jumper on both sides.
If construction goats will be madewith your own hands, in addition to the elements described above, you will need an adjusting mechanism that will help to level surface irregularities. To form it, you need to purchase four bolts, as well as nuts. Bolts should be selected in diameter, the minimum figure which should be 20 millimeters. In the lower part of the racks should be welded the nut into which the screw is installed.
When are the goats building their ownhands, then begin work on the formation of the pin design is necessary from the racks. In this case, everything is quite simple, at the bottom of these elements you need to weld the nuts for the bolts. In the upper part of the welded pipe. It will need to be used for mounting the next tier section. On the sides of the pipe above and below, stepping back from the edges of 200 millimeters, it is necessary to weld tubes whose length is 100 millimeters. On top and bottom of them should be four pieces. The result should be a cross, which will allow, connecting the racks with jumpers, to form a rectangular structure. Racks of the upper tiers will differ from similar elements below the lack of nuts. In this case, the pipe must remain free.
If you make scaffolding,The next step along the edges of the horizontal long and short jumpers will need to be welded the pins, bending them thereafter at a right angle. It is important to provide the structure with a rack, which should have parts made of thick boards. Their width should be equivalent to 0.5 meters. In the process of assembling the rack is placed on a horizontal short jumper.
Making metal scaffolding, onthe next step will need to be assembled. For this master is recommended to enlist the help of another person. One of them will have to hold two racks, while the other will have to insert jumpers in them. With the help of short elements you will be able to assemble two sides. Each of the masters, holding the sidewall, begins to insert a long jumper. After these blanks are in place, you can trim all the level, laying on them ladders. Before making construction goats, you should be familiar with the technology. At the next stage, it assumes the possibility of installing subsequent tiers, while it is necessary to use the above described method.
Если вы решили изготовить козлы из древесины, то the spacing between racks can be equal to the limit of 2 to 2.5 meters. As for the width of the flooring, it should be equivalent to one meter. You should not make the structure too high, the maximum height limit is 6 meters. For the work to be prepared boards with a thickness of 50 millimeters. As for their width, this figure should not seem less than 100 millimeters. It is possible to replace such blanks with a square-section bar of 10 cm. Round timber can form the basis of the supports and stops. Struts and fences, as a rule, are made of planks, the thickness of which is 30 millimeters or more.
If you want to make goats constructionfolding, which was discussed above, they can be used for many years. This is not the case with wooden structures that require treatment with certain substances that provide the material with special qualities. Wood serves less and is not as stable in the finished structure. Among other things, wooden wheels should be installed on special stages, which exclude the interaction of lumber with the ground. Drawing construction goats will allow you to carry out the work without errors. You can borrow it from the article or draw it yourself depending on the size of the future construction. After all, it will depend on it how convenient it will be to carry out construction work.
