In the installation of building structures and installationfinishing coatings the most attention is paid to the base material - in this case the flooring. Work with the roof involves the placement of roofing materials, taking into account the requirements for the operation of the house. However, even under the condition of high-quality installation of metal-tiled coatings, the roof will not fulfill its protective functions unless the master has taken care of tightness. Invasion of the roof structure, caused by the need to implement technological exits, inevitably violates the integrity of the coating. Optimize and in some cases make the formed gap manageable will help the passage element for metal tiles, which will preserve the main function of the technical hole, but also minimizes the impact of negative weather factors.
In essence, it is a small cap thatmounted on a previously prepared foundation in the roof. That is, a hole is first made, and then it is closed with an appropriately sized chimney or ventilation accessory. It is important to note that the ventilation elements for metal tiles can be made of different materials, the choice of which should be approached responsibly. For example, plastic elements are very practical and easy to install. Also, they are not afraid of weathering, corrosion and wind. But they do not compare with stainless steel in terms of strength.
Как правило, конструкцию проходных элементов form three parts - the base of the cap, the tube and the head for removal of exhaust air, smoke or various impurities. From the point of view of installation, the entry element for metal tile is the simplest component of roofing fittings. The installation technique is simple, but much depends on the skill and attentiveness of the roofer, since any deviation in the arrangement of the element will reduce its performance.
The site in which you plan to installEntrance system, prepared not only by cleaning the surfaces, but also by upgrading the structure. In advance, a system should be provided for the entry of air masses into the element wire. Next, a hole is created, and only after that you can finally prepare the site for installation. According to the characteristics, the passage element for metal tile as a whole corresponds to modern roofing, therefore it is not difficult to reduce two types of material. But for the correct fit of the sealing parts, it is nevertheless necessary to correctly clean the surface of the installation site and perform a degreasing operation.
To form a hole should be at the highest pointcorrugations and at a sufficient distance from the junction of two layers of metal. Next, using the template sheet, which usually comes bundled with the fittings, it is necessary to draw the cut outlines. Usually, metal roofing under such conditions is opened with an electric jigsaw. In order for the flue element for the metal tile to be installed smoothly, care should be taken of the exact placement of the clips and sealant. The rubber lining integrates into the formed niche, covering the opened edges. Depending on the structure of the roofing cake, sometimes trimming of insulators is required. In this case, you should also prepare sealing putty that will fill the contours of the connection of the through device and the insulation material.
Implementation is carried out directly inmade a hole so that in the future it was possible to fasten the complete hardware in the clips installed in a niche with a seal. Manufacturers in the factory make mounting holes along the entire circumference of the passage element, therefore, during the attachment process, you can do with a screwdriver or a screwdriver. The main thing is that the passage element for metal tile should be tight and without gaps. It is not worth saving on sealants, since the reliability of the roof covering as a whole will depend on the density of the location and the absence of through sections.
High-quality roofing accessories producesVilpe company. Its lineup contains components of different configurations, sizes and stylistic designs. Technologists regularly improve and plastic materials from which the basis of products. True, this product is not cheap - about 5-6 thousand rubles. As for specific models, specialists have gained special confidence in the Huopa and Vent series. Also, technological advantages are demonstrated by the latest line of the manufacturer - Muotokate. This is a flexible and therefore multi-functional element of the Vilpe. In this case, metal tiles gently and gently engage the flange without the risk of damage. Alternatively, it is necessary to offer and products "TechnoNIKOL." Although this line demonstrates simpler and even budget solutions in individual families, such prospectors pay for their cost with their quality.
Functional and reliable roof - a pledgesafe operation of the house. The main emphasis in the work on the construction and external provision of the roof is still on the creation of a durable coating. The same metal tile, together with waterproofing materials, must comply with the operating conditions in a particular region. However, do not underestimate the tasks of auxiliary accessories. For small out-of-town houses and cottages, a passage element for the TechnoNIKOL metal tile, which consistently provides the basic functions of ventilation and the chimney system, is quite suitable. Objects, in the construction and finishing of which expensive materials and complex trusses are used, it is desirable to provide with a walk-through system of the Vilpe brand or products of the same level. If desired, in the future, such a device can be supplemented with other optional solutions that increase the operational capabilities of the roof.
