Saw "Partner 350" has decent power andvery convenient to use. However, the flywheel in this model is not designed for continuous operation. If the motor overheats, various damage may occur. In order to make repairs yourself, you need to know the device of the "Partner 350" chainsaw.
Стартер довольно часто выходит из строя.In this case, repair the chainsaw "Partner 350" with your own hands you need to start with the following: unscrew the side cover, which is located next to the gearbox. The starter of the saw is located near the engine. In order to inspect this detail, the air damper is first removed.
Next you need to disconnect the carburetor.The starter in this model is connected to the throttle. To separate them, you need to use a screwdriver. If the starter can see carbon, this part will have to be completely replaced. In this case, installed the usual modification, and find it in the store is not difficult. However, the best parts for chainsaw "Partner 350" to purchase in specialized workshops. After replacing the starter, it will only be necessary to fasten the throttle again and place the carburetor with the cap.
Маховики в данной пиле ломаются довольно редко.Most often this happens precisely because of the engine overheating. In this case, repair the chainsaw "Partner 350" with your own hands you need to start with the removal of the protective cover. After that, the engine is first examined. In some cases, the tire may burn out. If there is no darkening on it, it means that you can immediately twist the flywheel.
To make it easier to get, you needfirst disconnect the crank. It is located directly above the flywheel. To do this, you need a Phillips screwdriver. After that, the flywheel can be easily unscrewed from the panel. Especially carefully you need to examine his head. If it is deformed, then the flywheel will have to be replaced. In this case, it is necessary in the store to say the exact diameter of the head.
Поломка барана в пиле сопровождается громким sound when you turn on. In this case, repair the chainsaw "Partner 350" with your own hands you need to start first with the inspection of the fuel system. The problem may be in the failure of the carburetor. In some cases, the drum crashes because of the crank that comes out of the grooves. In order to inspect it, you need to open the protective cover. Next, remove the throttle and check the fuel system.
All tubes must be connected.After that, you need to inspect the crank, which is located above the carburetor. If he flew off the slots, you can adjust it yourself. However, if it is severely deformed, it will have to be replaced. The drum in this saw is located near the air damper. When it beats on the clutch, its protective ring is damaged. If it is completely ground, then the drum will have to be completely replaced. In this case, you need to know the labeling of the product. In the installation of the drum is quite simple, and you can cope with the installation yourself. In this case, it is only important not to damage the fuel system during repairs.
The connecting rod mechanism is quite complexchainsaw "Partner 350". Malfunctions are often accompanied by the loud operation of the motor. It should also be noted that when a connecting rod breaks, the carburetor often fails. In this case, repair the chainsaw "Partner 350" with your own hands, it is better to start with an inspection of the ignition module. You will also need to completely check the clutch. In particular, attention should be paid to the state of the centrifugal clutch.
In order to inspect it, you must removetop cover. Directly coupling this model is located near the carburetor. To get to the centrifugal clutch in the saw, the flywheel is removed. Next, the carburetor head is disconnected. In this case, it is important not to damage the fuel system. Fastened to the centrifugal clutch bolts. You can disconnect this part with a key. If there are cracks under the cylinder, then the clutch will have to be changed. However, some experts advise not to hurry. If the cracks are shallow, you can try to shake off the surface with a file.
The breather of the presented model clogs whenlow-quality fuel is used. In such a situation, the repair of the piston chainsaw "Partner 350" must begin with a carburetor inspection. In order to see it, you will have to remove the top cover of the device. Next, the ignition module is twisted. After that, it is important to disconnect the crank immediately. In this case, you have to use the keys. The next step is to disconnect the drum.
Immediately behind it is the carburetor.Remove it for inspection is not necessary. The choke is checked first. In some cases, the problem may lie in it. If the throttle is OK, you need to look at the tire. When it is damaged, its sides are a bit knocked down. There may also be cracks in the center of the tire. If the part is deformed, it will have to be replaced. Parts for chainsaw "Partner 350" to get better in specialized workshops. Independently put the tire on the carburetor is quite difficult. In such a situation, it is better to consult a specialist.
To fuel is very demanding chainsaw "Partner350 ". The carburetor is repaired when its nozzles are contaminated. In this case, all the internal mechanisms should be inspected. When a fuel leak occurs, a trace should remain on them. If the hoses are OK, you should inspect the carburetor directly. To do this, remove it first cylinder. Next, it is important to remove the crank, which is located next to the clutch.
После этого появится возможность посмотреть на carburetor. It consists of the lower unit, as well as the upper part with the ignition system. To unscrew the part, you have to use keys. After disconnecting the carburetor need to inspect its base. If it is not deformed, then the problem lies in the ignition system. In particular, contacts may burn out. Separately, they, unfortunately, are not replaced. In this case, have to buy a new carburetor. Installing it will be pretty easy.
To control the circuit, a specialcatcher, which has a chainsaw "Partner 350". Faults of this type are the result of improper use of the device. As a result, the circuit may sag after a while. In such a situation, repair the saw should begin with an inspection of the sprocket. It is located near the handle. To remove it in this case is not necessary. If the sprocket teeth are not deformed, you can simply try to lubricate them with engine oil.
Next, it is important to inspect the trap.In the device, it is quite simple and is a set of rollers. When the catcher fails, they are knocked out of the chain. Independently to set them impossible. The only option is to put a new catcher. To do this, use a screwdriver. Its fixing is carried out on three nuts. When installing the catcher should be noted that the rollers are located in the upper part and must be near the chain.
If the chainsaw "Partner 350" does not start,Perhaps the problem is the throttle. In this model, it is connected directly to the clutch. When there is a large load on the engine, it does not stand up and bursts. In such a situation, repair of the saw must begin with inspection of the coupling. In order to get to it, you will need to unscrew the protective cover of the model. Then you just have to remove the crank.
After that, it will be possible to inspect the clutch andthrottle. In some cases, it flies out of the clip. In such a situation, you do not need to buy anything. However, if a gap has occurred, then a new throttle will be needed to repair the saw. In order to install it, it is important to unscrew the clamp first. It is fixed with just one bolt.
