Roller shutters in the toilet today install alla greater number of apartment owners and private houses. This design is designed to hide communications in the false-wall. Not only water supply and sewage systems can be located in the floor space, but also filters, water heaters, as well as water meters. Such an addition to the bathroom will not only be practical, but also quite attractive, as well as functional. Roller shutters can be installed during the repair of the premises simultaneously with the replacement of communications and installation of meters, as well as additional equipment. This requirement is due to the fact that it is at this stage that a niche is formed, and a curtain of appropriate size is selected. Consumers choose this approach also because it allows easy access to the pipes. Choosing roller blinds in the toilet, you should not try to save, as high-quality products of this type can also provide a fairly good noise insulation.
Перед тем как приступать к работам, необходимо to get acquainted with the characteristics of the described products, it will allow to carry out installation work, which will not begin to suggest the need for alterations. Roller shutters in the toilet are a canvas, which consists of slats. From above the curtain is wound on a shaft located in a protective box. Inside the upper part there is a spring, which is designed to balance the weight of the canvas, excluding the unwinding of roller shutters under its own weight. This function is necessary for fixing the lamella without any attachment. Before the start of manipulations, it is necessary to measure the width of the opening, if this indicator is less than 52 cm, then the rolling shutters cannot have a spring mechanism. For this reason it is necessary to mount the blinds, which have a cord mechanism.
If you decide to install roller shutters in the toilet,you need to know about all the methods of installation. The process can be carried out in such a way that the box is located inside, outside or superimposed on top. The way of work should be chosen, taking into account the specific design of the opening.
A more optimal solution isexactly this approach. At the same time, it is important to make sure that the communications allow for the deepening of the box. Measurements need to be carried out after alignment of walls is finished. But these manipulations are made before laying tile. This will fix the structure on the wall. Later, when used as a finishing decorative material for a tile, it should be started to be laid from the installed structure, gradually moving towards the doorway. At the same time, it will be possible to obtain the effect of embedding the guides on the thickness of a single product. While the seam located between the guide and finishing materials, will be completely invisible.
Если вы решили установить рольставни для sanitary cabinet in the toilet, then you can carry out the work by installing the box outside. This option is relevant in the case when communications are in close proximity to the opening, and the box is not possible to be located inside. Measurements should be carried out after the tile is on the side walls. Mounting will need to be made directly to the decorative material.
Плитка, которая укладывается на боковые surface, should go into the opening of 5 cm. This will leave the concave side of the structural elements visible. If the lining has already been completed, then the design should be refined by installing it on the tile. Mounting in the opening will reduce the useful width by double the width of the guide. This figure is 53 millimeters on both sides. The useful height will also be reduced, but in this case to the height of the box. If the opening is very low, the box will take an unacceptable amount. If you install rolling shutters for the sanitary cabinet in the toilet, it is important to choose the correct box dimensions that should correspond to the height of the opening. If the height of the structure is impressive, the full opening of the space will require a more impressive number of turns to be wound on the shaft.
Рольставни в туалет своими руками могут быть installed inlay. This option is used when the structure is located on a sufficiently thin wall. An example is the case when drywall was used as a base, and tiles were laid on it. Top mounted guides. With this method, additional fixation to the surface of the ceiling is not required. For this reason, it turns out quite reliable and simple design.
Installation of roller blinds in the toilet involvescompliance with several stages, as the first installation of the box acts. For carrying out these manipulations, decorative protection is removed from it. Then the master must make a fixation between the niche walls, which are located opposite each other, the attachment can be made to the front. The last option involves fixing to the wall on which a niche is formed.
Сделать это сможет любой домашний мастер, для This requires the use of a punch, with which you can drill holes. They are installed cork, which will hold the screws or dowels. Fasteners are installed through the holes in the housing.
This component of the system, which will bego to the canvas, installed on the floor or a special box, which is designed to limit the length of the niche. Fastening of a level is made by two self-tapping screws which are established in previously formed openings.
Before installing the roller shutters in the toilet,It is important to adjust the guides in size. To do this, determine the distance from the feigned strip to the bottom of the drum. This indicator will determine the length of the guides. Their installation is made on the same technology that was used for the installation of all elements of the system. Apply here you need screws, which are installed in the end of the niche. Installing the roller shutter in the toilet may suggest some difficulties that are associated with placing the canvas in the guides. In order to facilitate the work, you first need to place the place where the guides will be fixed. After they start up the canvas. At the next stage, the master must produce a final fixation of the guides.
Roller blinds for the closet in the toilet afterthe implementation of all the above manipulations can be considered ready for use. Will only close the lid, which belongs to the box. Professionals are advised to order the products described in the final stage of renovation of premises in the bathroom. It is recommended to do this after the niche is fully formed and ready. It is necessary to finish the ceilings and walls. However, one should not hurry with the installation of sanitary devices, they are mounted after the shutters are in place. This is due to the fact that the installation work, which involved blinds, will be difficult when the toilet or sink is installed, which obstructs the opening.
When choosing roller blinds, you must considerinterior features and shades possessed by decorative materials used in the repair of the room. Only in this way will it be possible to ensure that the finished roller blinds (to the toilet) look harmoniously with all the elements of the bathroom.
