A clothes hanger with your own hands may wellbe made without the help of professionals. To do this, it will be enough to prepare all the necessary materials and tools, as well as get acquainted with the technology of the work.
As a material that will form the basisdesigns, planed pine boards will perform. It is necessary to choose those that have a thickness in the range of 25 millimeters. In order to supplement the shelves of this product, which will be strengthened on the wall, you should use a glued furniture shield with a width of 300 millimeters.
If a clothes hanger will be madewith your own hands, you will need to prepare wood screws, PVC glue, acrylic moisture-resistant varnish for wood, as well as an electric drill. You will need a jigsaw, a hacksaw, a tape measure, a ruler and a square. Wooden clothes hangers are made using abrasive pelts, a hammer, a screwdriver, a circular hand saw, and stains. The latter is necessary if there is a need to change the color of the structure. In order to make the product more aesthetic, you need to stock up with wooden furniture panels, and furniture dowels, the dimensions of which are equal to 10x30 millimeters, will act as fasteners.
If you make a hanger forclothes with your own hands, then after all the tools and materials are prepared, you can proceed to the manipulation. All parts must be well treated with abrasive sandpaper, especially for sharp edges and corners. The first must be rounded. Blanks should be rid of chips and burrs, as well as other irregularities that are striking. In the process of work, it will be necessary to observe a certain technology, which involves several stages. When making a clothes hanger with your own hands, then on the table initially you need to lay two boards that will be oriented vertically during operation. After they need to put the transverse boards in the amount of 3 pieces. Once the right angles are aligned, you need to screw in the screws, installing them on the back side of the transverse planks. This will connect all the details together.
In the manufacture of clothes hangers in the hallwayScrews need to drown in such a way that the heads are flush with the surface of the transverse parts. The sharp ends of the screws should not go through the vertical boards. In the next step, you should fix the remaining vertically positioned boards, providing a uniform clearance between them. The width should be equal to 80 millimeters. It is important to check and if necessary adjust the right angles. Now, under the crate, you need to have a holder for hooks, and then insert two fasteners on each vertically positioned board. In the manufacture of clothes hangers in the hallway at this stage, the screws should be installed on the back side of the transverse parts. This will give the structure additional rigidity.
After the master managed to carry out allthe above work, you need to dock the shelf with two sides, which serve as brackets. You need to make the sidewalls in advance. Wooden hangers for clothes are obtained most quickly if an electric jigsaw is used in the process. With it, on a previously defined contour, you need to cut the workpiece, processing them with abrasive sandpaper. To install dowels you need to drill holes in all blanks. 4 shkanta are installed in the regiment; PVA glue should first be applied to them. The sides are connected to the shelves by means of dowels, which are inserted into the prepared holes. On each sidewall you need to cut in two fasteners.
If a clothes hanger will be made,which photo you can see in the article, then in the next step you can assemble the whole structure. Due to the fact that the load from the items on the shelf will affect the sidewalls, they must be fixed to the vertical outer boards of the batten system as reliably as possible. To do this with screws, you should additionally use furniture dowels. At the previous stage, holes were drilled in the ends of the sides. They need to be treated with glue, having hammered the dowels into place. When you will make a hanger for clothes, the photo of which will help you to determine the design features, in the extreme vertically located boards you will need to make holes corresponding to the previous ones. It is important to ensure the correct docking of the pre-assembled shelf. To fix this element of the sheathing is necessary with screws. Self-tapping screws are installed on the rear sides of the vertical elements - two pieces for each sidewall. After the regiment is fixed to the upper face of the element on which the hooks are mounted. In this case, you can do even one screw.
The hanger drawing presented in the article will allowyou prepare the elements for assembling the structure. Depending on the area of the room, you can adjust the dimensions, taking into account your own preferences and features of the exterior. It is important that the subject is combined with the situation.
