The dimensions of the parquet boards may vary.It all depends on the kind of material. It is a wooden covering, which can be piece, mosaic, shield, as well as artistic or massive. In this list, not all varieties of parquet boards, which will be discussed below. In order to make the right choice, you need to understand the characteristics of each type, as well as learn more about the dimensions.
The most popular species among the brethren todayis a piece parquet, which is a bar with a lock joint in the form of ridges and grooves. The material is based on solid wood. The thickness of such laths can vary from 15 to 22 millimeters, and the length can be equal to 50 centimeters. Among the advantages of such a coating should be allocated the possibility of repair, a long life, as well as a variety of stowage technology.
If you decide to choose a piece of parquet, you canselect one of the existing classifications according to the drawings. The pattern can be small, contrasting, often repetitive, textured, strongly varying with different shades and changing with small knots.
The sizes of parquet boards of a mosaic type canbe equal to 40x40 or 60x60 centimeters. The thickness varies from 8 to 12 millimeters. During the installation, you can lay out a mosaic or pattern. The front side of this parquet is protected by paper, which is removed after laying. If necessary, increase the soundproofing characteristics of the floor. For this purpose, materials with the appropriate qualities are glued to the underside of the board.
This kind of parquet board is divided intoprofile grooves. If there are oblique folds on all sides, then there is a material in front of you, where a rivet is installed along the edge. Such products are the most durable. The strengthened fastening is established on perimetre of a lath where there are oblique grooves. High strength can be obtained by using a mosaic parquet board with fastening on a hard surface. The slats are nailed to the base while the panels on both sides have grooves and ridges.
Dimensions of hardboard boards can beto reach 80x80 centimeters. The thickness varies from 15 to 30 millimeters. The face layer of such products is varnished. With their help you can create square shapes and their derivatives.
Laminate is an artificial substituteparquet board. It has four layers. The basis is made of fiberboard and chipboard. The thickness of this material varies from 7 to 11 millimeters. The boards are quite easy to lay down using the floating floor technology.
Massive board is made of solid woodand has a punctate joint. The width of the products can exceed 8 centimeters, and the thickness - 15 millimeters. The length of the product is several meters. Among the advantages of the material should be allocated a wide range of colors, durability and exquisite appearance.
There are standard sizes of a parquet board,which determine the length, width and thickness of the product. The first parameter varies from 110 to 250 centimeters, the second - from 12 to 20 cm, while the third one - from 1 to 2.2 cm. Often the masters use materials having the above-mentioned standard sizes.
The size of a parquet board, whose standarddetermines GOST 862.3-86, will be individual, depending on the variety of material. For example, Barlinek products have a common size of 2200x207 millimeters. But if we are talking about the firm Tarkett, then it offers floor coverings with a wider run-up in size. You can meet the following dimensions of the board: 2215x164x14; 2283x194x14; 1123x194x14 mm. If you choose large dimensions of the parquet board "Tarkett", you will be able to complete the repair work on the finish of the floor in a short time.
After you have decided which sizesParquet boards are suitable for the premises of your house, you can start laying the material. If the thickness does not exceed 1.4 centimeters, the laying may be carried out in a floating manner. Or by gluing to the base. If thicker boards are available, they should be glued. During the operation, such a coating is polished several times. Recently, manufacturers are increasingly offering materials for sale with a groove joint, which allows you to create floating attachments. As an additional advantage of this technology is the opportunity to replace the damaged areas without dismantling all the coatings.
Parquet board, laying, the size of which youcan be studied independently, require an even foundation, excluding the presence of potholes, adhering dirt and rushes. If the parquet board has a thickness varying from 13 to 15 millimeters, it can be used for the device of a warm water floor. This belief is true in the event that the system is in a screed five centimeters thick. The temperature should not exceed 27 degrees. The installation of the material can be carried out on the old parquet. However, the elements should be perpendicular to each other. The dimensions of the parquet board and laminate were mentioned above. These values will allow you to calculate how much material you need to purchase. To do this, determine the floor surface area, and then divide this value into the area of one panel. This way you can calculate how many boards you need to purchase. However, experts advise buying material with a margin of 15%.
If you decide to choose a variant of a parquet board,which does not have a lock joint, and its edges are even, then it is necessary to lay this coating on the glue. The composition is applied to the joints of the boards. They need to be firmly pressed against each other. Due to the wedges installed at the edges of the floor covering, the products fit securely.
Installation usually begins along a longerA wall that should not have doorways. The first board is located in the far corner. Between it and the wall, wedges of equal thickness should be laid. Between the entire plane of the floor covering and the walls, an 8 mm gap should be formed. The same technology is followed by the following boards. The next row begins with the remaining segment. It can be a piece of the board of the previous row. But if there is a picture, then it should be followed. Perhaps you need to cut the excess to combine the ornament.
The boards should be applied with a lock to the previous onerow at an angle of 25 degrees. You should feel when all the junctions begin to converge. To speed up the process, you should use an ordinary rubber mallet, which products are adjusted to the place. After the assembly of the flooring, you need to get rid of the wooden wedges that were previously laid between the boards and walls. They will allow to create a so-called temperature gap, which compensates for the expansion with changes in humidity and conditions in the room.
