Houses from a beam look very attractive, butIf you own another type of building, you can sew it with imitation of a bar. This decoration has been enjoying popularity more and more recently. For its production a high quality wood array is used. This cladding material is a wooden panel that is more affordable in comparison to a natural counterpart.
Facing has a negligible weight thatfacilitates transport and installation. The imitation of a beam for finishing not only outside, but also inside premises is used. Installation work involves the docking of products closely, intermediate grooves in this case is not formed.
This material has high strength, itIt is durable, resistant to climatic factors and other aggressive environments. This decoration allows you to make the walls more warm and soundproof. And if you additionally use a layer of insulation, then you will make your home resistant to wind and frost.
Sheathing by imitation of a bar assumes preparationpanels. They are realized packed in a sealed film, because under the conditions of the plant they are subjected to chamber drying, so that the wood does not absorb excess moisture from the air. Before the beginning of finishing works, the products are removed from the package and left for 2 days in the environment where they will be used. Otherwise, the geometric dimensions of the panels may change - the finish will be skewed.
The next step will be the processing of woodenpanels with antiseptic substances. It is much easier to do this until the time of installation, and technical locks will not be available after that. If the panels are not painted yet, then at this stage they are covered with a layer of varnish or any other selected composition.
Sheathing of the house by imitation of a beam does not manage in any waywithout laying the waterproofing layer, which can be a PVC film or parchment. Fasten the material directly to the wall. Cloths between each other are lined with an overlap of 15 cm. Joints should be glued with aluminum tape.
Для дополнительной прочности к стене полотна fastened with a construction stapler. It is important to ensure that the waterproofing does not sag, however, it is not worth it to pull it too tight. This recommendation is due to the fact that the film can tear as the temperature changes. Do not be afraid that the waterproofing will depart from the surface of the wall, because it will be pinned crate.
Timber imitation by handprovides for the installation of a crate. If the wall is flat, then for this purpose a beam of wood with a square cross-section in the range from 30 to 50 mm is used. For curved walls, a metal profile with mounting brackets is used. Mount the crate to the wooden walls recommended 40-mm self-tapping screws. The pitch of the lath usually depends on the parameters of the insulation, but a fairly thick imitation of the bar has an impressive weight, so for outdoor applications, the distance between the elements should not exceed 60 cm.
For internal work, this parameter canto make 80 sm, after all panels will be more thin not only in thickness, but also in width. In addition, their weight is much less. The lining of the house from the outside with imitation of a bar can assume the presence of two systems of a lathing. The first in this case is installed horizontally.
Insulation is required only with exterior decoration,this difference is the main in the methodology, which involves the installation of the material from the inside. This stage allows you to move the dew point and make the walls warmer. The insulation must be located close to the crate. Unfilled areas should not remain, joints should be as tight as possible.
Sheathing by imitation of a bar outside canprovide for the laying of insulation in 2 layers. The number of layers will depend on the climate in the region of work, as well as the targeted use of the house. Mount the heater can be fungus or tape. Acquiring matte thermal insulation, you should remember its standard width, which is 60 cm. As for the foam, this parameter is 1 m, so the canvas will have to be cut.
Simulation of the bar is performed by a certain algorithm. Install this finish can be on the walls of different materials, namely:
After completion of the work, the walls will look like those,that are made of natural timber. Installation work is not difficult. Profiles are complemented by grooves and spikes, which allows them to fit tightly to each other. The boards are fixed horizontally. Sheathing by imitation bar allows the use of a universal material that is combined with a profiled or glued beam.
Quite often recently you can meetBaths and rooms of houses, which are lined with such material. If it is an external finish, then the products can be used on the walls of buildings made of foam blocks, carcass and concrete. Fixation is carried out on the crate, which is performed in the form of bars. Elements of the frame are located along the entire perimeter of the walls, the distance between the slats should be approximately 50 cm.
For the reason that imitation of the beam is fixedhorizontally, the fixing of the bars should be carried out vertically with the help of self-tapping screws. In order to make the walls warmer, you can also lay a thermal insulation of natural materials, namely ecowools or mineral wool.
Обшивка имитацией бруса предполагает крепление another layer of waterproofing over the crate. After that, you can start installing the cladding. The installation should proceed from below, it is there that the casting board is fixed. Place the products with a comb up. Screws are screwed into the spike of the board, the hat is recessed 2 mm. When laying the next board, you must position it with a groove in the spike and adjust the products to each other. At an angle of 50 °, a screw is driven into the spike. The last row is set on self-tapping screws. The places where the fasteners were installed can be sealed with nails and polished. After the completion of the installation work, proceed to the puttying and painting of the beams.
Если имитацию бруса вы решили использовать для interior decoration, then follow the technology described below. For such work, it is recommended to level the walls so that the space of the room does not decrease too much. The surface is cleaned of dust and dirt, and then a layer of vapor barrier is installed on the wall.
Next, a crate of material must gois chosen taking into account the specifics of the premises. The lining is installed vertically. On concrete and brick walls, the installation is carried out using dowels, in the case of wood it is possible to work with self-tapping screws.
If the casing is imitated with a barinside the premises, the conditions of which are high humidity, then the elements for the frame must be treated with an antiseptic. In addition, for galvanized areas, a galvanized profile can be used. The panels are installed horizontally. The method of fixing them is similar to that used for finishing the facade. Klyaymery can be used as a fastener, but for the ceiling this approach is not reliable. It is better to use small carnations or screws. They are clogged or screwed into a spike at an angle of 45 °.
Sheathing walls imitation timber does not implyfastening products in the facial way, if the work is carried out indoors. This is due to the fact that hats due to the small thickness will be very difficult to hide. When connecting panels at the corners, inner and outer corners should be used, they are usually realized together with the finish. After completion of the wall can be sanded and apply a tinting varnish. Already painted panels are usually sewn to the ceiling, this simplifies the work.
