Many plumbing users are faced with the problem of how to flow. Water can leak both in the barrel itself and in the bowl. This is an unpleasant, but reparable situation.
Before troubleshooting and troubleshootingit is necessary to understand the structure and operation of the tank for draining. Its defining function is to supply the required amount of water in order to flush the toilet bowl after use. The material for the tank can be ceramics, if it comes with a bowl, or plastic and stainless steel, if the tank is installed separately. Frequent breakage of plumbing becomes the fact that the toilet bowl passes water into the toilet.
Механизм спуска может быть либо грушевого типа, or siphon. The latter produces a lot of noise when it is in operation, as water is drawn on the siphon principle, and the water drains when you press the button. The work of the second mechanism is different in that when the button is pressed, the pear rises, and after the water has descended, it closes the drain hole again. In order to avoid the overflow of water with a pear or protect it separately from it.
Modern drain mechanisms save moneywater, as they are set in two modes, allowing to drain not all the liquid, but only a part, if that is enough to wash the bowl. But this is not a guarantee that there will be no problem when the toilet bowl passes water into the toilet.
Before you get started, you need tocheck which of the mechanisms is on the tank being repaired. At the same time, the lid of the toilet bowl should be pushed aside carefully, since with possible breakage it will be difficult to find this item separately for sale.
Many home wizards face a problem when the toilet bowl passes water into the toilet. What to do?
If plumbing is installed recently, it will flowmay due to improper installation. If only a few months have passed after the start of use, and a malfunction has already appeared, most likely this is due to the poor quality of the fittings, and as a result, premature failure. Serious damage, due to which the toilet bowl passes water into the toilet, does not occur often. They can declare themselves only in three years. The main ones are:
- the toilet cistern leaks water continuously due to overflow;
- leakage in the toilet;
- breakage in the drain button, when it responds only to repeated pressing.
Any of the damage to be corrected, you only need to correctly diagnose it.
Plumbing cracks appear on severalreasons. Most often it is the wrong installation or expired product life. Excessively tightened bolts at the junction of the tank and bowl will cause ceramics to crack. If the cracks penetrated into the drain tank, then it can only be repaired temporarily, but this is enough to get a new one.
Итак, нужно сначала слить воду, затем тщательно dry the surface, then seal the crack with a special sealant. But with the bowl, the situation is more serious if there is a crack in it, for any of the reasons, it will have to be replaced, because repair options do not exist.
Often the reason for the leak lies in the fact that the float in the cistern of the toilet bowl passes water.
Excess fluid is drained over the edge of the tank.Perhaps the case in the lever of the float, which is slightly shifted or twisted. It is necessary to inspect the float, and for this to remove the cover. Its optimal position is 2.5 cm below the nozzle. When the float deforms, it will not function properly, because water will fall into it. To seal the cracks in the float, a sealant is suitable, but for this, the element needs to be pulled out and dried well. Again, the sealant is not the way out, but only a temporary solution, so you have to buy a new hardware.
If the item is free from defects, and water is stilloverflows, it may be the case in her head. With its high power, the float is pressed with water, which gives it a way out over the edge. But if the design includes a stabilizing valve, this problem will not arise.
Another kind of problem when the toilet bowlit passes water into the toilet, is connected with another - when you have to press a button several times to flush In this case, a malfunction in the membrane. It must be rinsed with water to remove any salt deposits.
If this element is deformed and hascracks, then it must be replaced by doing the following: at the bottom of the barrel find the siphon nut and loosen it, then remove the siphon itself. After replacing the membrane, install the siphon in its place. You should choose a membrane that is identical to the former. When the siphon is removed, you need to check other parts for defects. Often, polymer structures are covered with cracks, and oxides are formed on the metal. If the latter can be cleaned, the plastic is not always subject to recovery, which will lead to a complete replacement of the tank.
The cause of this breakdown may be defective thrust. You can replace it with wire for a while, and later acquire a new one.
When the toilet bowl is flowing, it passes water intothe toilet may have a broken constipation mechanism. This malfunction cannot be eliminated by replacing several parts. You need to buy a whole set of a node, and not look for parts that are not always sold separately.
Одной из причин образования течи может стать и digging on the tank. The return spring may loosen, causing it to jam in the rod, causing a permanently open drainage door. In this case, you can eliminate the problem by replacing the spring or the button itself.
If it became noticeable to flow where the tankconnects to the plumbing flexible hose, the first way to eliminate it will be tightening the connecting nut. If the thread is loose, it can be sealed, but a broken thread or a broken hose will have to be completely replaced.
If the toilet bowl passes water into the toilet, replacing the gum can help at the junction of the tank and bowl.
При появлении течи в подобном месте следует inspect the tank for cracks. If they are absent, then the cuff remains the likely cause of breakage. It connects the tank and the bowl. It can be made of metal or polymers. Depressurization of the joint contributes to the displacement of the cuff, troubleshooting is simple - fix the element and tighten. Time can affect this part, so sometimes it requires a complete replacement.
Второй вариант проблемы кроется в резиновой gasket, which is located between the bowl and the tank. Incorrect installation leads to its offset. Over time, this part also fails, cracks and deforms. If there are no changes on it, then it should be carefully put in place and the bolts tightened. Insufficiently tightened nuts on them can cause leaks, but you do not need to overdo it in this business, otherwise there is a risk of damaging the ceramics.
Often a wet stain appears under the cistern due tocondensation on its surface. This is due to the fact that there is a difference in the air temperature in the room and the temperature in the tank. You can eliminate this trouble by improving the air exchange in the room, as well as in the application of a two-level drain.
Причин течи в бачке унитаза не так много.If you know them and follow the instructions for elimination, then even a professional can not cope with it. The main thing is to act confidently and carefully, then plumbing will serve for a long time.
