Plywood - building material, activethe use of which requires the production of furniture, packaging and even automobile manufacturing. For the production of this multilayered material there is a wood veneer of coniferous trees. The result is a sturdy construction, which can be fastened with screws, nails and bolts, but the most convenient option is glue.
How to glue the plywood to the plywood?The most environmentally friendly is water glue. It completely lacks the smell, it can be diluted with water and used instead of a primer. This laying requires additional fastening, and the main drawback is long drying.
Slightly less dry adhesive, based on the solvent - 3-5 days. In this case, it is necessary to pre-impregnate the concrete screed with a special primer. The disadvantage is a sharp smell.
How to glue the plywood to the plywood and save onThis time? Maximum satisfaction of this desire is possible through the use of a two-component adhesive. It dries for about 24 hours and does not need dowel-nails.
Deciding which glue is bestglued plywood to plywood, depends on the type of connection and further operating conditions. The process can be represented by an independent installation of plywood on the screed or carry an additional function, for example, to strengthen the structure.
If you plan to use unlinedplywood, then you can buy any glue. The main requirement is a dry and clean surface. To apply the composition to both glued surfaces, it is better to use a roller or brush. After this, you can strengthen the plywood connection with nails, screws or clamps. In the end, you need to remove the excess mixture.
How to glue the plywood to the plywood, if you use whole sheets? It is necessary to simply cover the surfaces with a mixture, and then press them with temporary dowel-nails.
It is not recommended to glue the laminated surface covered with a film, it is not recommended to glue it, therefore, before applying an epoxy compound, the sheets must be sanded with sandpaper.
How to glue the plywood to the plywood, so as not to disturbtexture of the material and not cause a color change, but at the same time get a high strength design? For interior work, PVA glue is ideal, and for exterior applications, phenol or epoxy glue.
The level of reliability of the joint is affected not only by the applied mixture, but also by strict adherence to recommendations, since if the latter is violated, the properties of the adhesive may not fully open.
At the base of almost any glue for gluing of plywood lie the following components:
The curing agent is usually any acid or ammonium chloride, and resistance to wetting guarantees the presence of tannic substances (formalin, copper salts, etc.).
Adhesive for plywood must have the following positive qualities:
It is equally important that the adhesive does not destroy the wood veneer and does not change its color.
Solving the problem, than to glue the plywood to the plywood, people often choose their "KS" or "Tabrikole".
A bit more about their properties and features:
The grade of a suitable glue for plywood is directly dependent on the level of strength required and on how high the humidity in the room in which it is planned to operate the structure.
How to glue the plywood to the plywood, if the finished product will be in a well ventilated room? Well suited PVA, protein or synthetic.
If it is planned to make dacha furniture, which will be located both indoors and outdoors, it is better to use one of the synthetic compounds.
After the choice was made in favor ofmoisture resistant material for the interior, you need to determine how to glue the plywood to the plywood. Feedback indicates that the compound is best carried out with compounds based on urea resin. The use of unlined sheets makes it possible to glue the plywood with any kind of glue.
The flow rate depends on the number of irregularities, the presence or absence of porosity and the quality of the screed. It should be based on the recommended flow rate of 1.2-1.5 kg / m2, but do not forget that the plywood mustbe laid on the foundation without voids. Only uniformly pressing the plywood to the base can ensure optimum distribution of the adhesive throughout the surface.
Before you start working with plywood, you should stock up on the following tools:
You also need to prepare the necessary materials:
Before you begin to work, you need to find out how to glue the plywood to the plywood. The instruction given below, as detailed as possible, reveals all the subtleties of this process:
About what to glue the plywood to the plywood, it was said a lot, but how to make something useful from this material?
After various repairs, a lot of plywood scraps remain, which are simply sent to the trash.
But these pieces are ideal, for example, to create an unusual and beautiful coffee table.
List of materials and tools required for work:
How to quickly make a plywood table? First you need to make a paper template for cutting out the legs of the product. The coffee table will look good on openwork or curved legs.
You need to take a large sheet of paper and draw feet on it at a scale of 1: 1. When transferring the picture to the cardboard, it should be remembered that the finished structure should be placed on symmetrical legs.
After completing work with the template, you canmove on to gluing plywood pieces. The construction of the structure must be carried out in such a way that the form resembles the future legs of the table. Bonding every 2 parts must be accompanied by the removal of excess mortar and tight squeezing of plywood pieces. At the end of the work, the legs should be placed on a flat surface, put a template over them and cut around its contour with a pencil. For trimming excess design need jigsaw. On top of the product should be placed tabletop and connect the parts together.
