In a modern office, old-fashioned stamps andpads replaced ergonomic automatic seals. Sometimes they are called traders - by the name of a well-known company that produces snap-ins for them. With regular use of the automatic trader, the ink on the cushion dries out, and the stamp imprint on the paper becomes pale and indistinct. Documents with pale prints are not easily photocopied and scanned. Legal departments of many companies can recognize such papers as invalid.
If you need to fill in the officea stamp pad, it does not necessarily have to call a specialized firm to find out how to fill the seal with ink. The refueling instruction is usually available in special boxes, in which automatic rigging is sold. The standard recommendation is to buy a new ink pad for printing. But this advice can be quite expensive for a company. So let's try to find out how to fill the seal with ink, without damaging it, and do not get dirty.
In standard automatic printing, the ink pad is in the middle. It can be seen from the side. A photo of the automatic printing with the position of the stamp pad is located below.
To understand how to fill a round sealink, you need to pull this pillow. To do this, you need to click on two buttons located on the sides of the trader, while slightly pressing down the print. If everything is done correctly and the automatic rig has not been damaged, the buttons will fix a slightly pressed state. After this, using an ordinary pencil, you should gently pull the pad from the side gap.
Before you print ink, you shouldclean the removed cushion and remove from it the sticky lumps of paint, pieces of paper and other possible contaminants. Different dents left on a soft surface, it makes sense to smooth a nongovernmental object. For this purpose, an ordinary clerical clip will perfectly fit. The end of it is carefully leveled out all the impressions. A worn pad is not elastic, it practically does not absorb ink, it shows deep dents that can not be smoothed out. It makes no sense to impregnate such a pad with ink stamps, it is better to order a new one - and then it will not be necessary to learn how to fill the seal with ink. The photo of the removed pads can be viewed below.
Thus, the print cushion is prepared forstains with ink. The required paint is produced by various companies, including in our country. In no case should it be printed with ink or other liquids - you can quickly and hopelessly spoil it. The standard bottle of ink has a dispenser, which is very convenient to drip paint on the print.
Several drops of ink should begently and evenly apply cushions to the surface. Surplus can be removed with a napkin. After painting, wait a few minutes for the liquid to soak into the surface. We insert a small pillow in an equipment for printing by ink side downwards. To answer the question of how to properly fill ink with ink, if two or three colors are used in automatic printing, you simply need to consistently pull out the pads of different colors and fill them with the appropriate ink stamps. The sequence of actions is the same as with single-color seals.
Recently, widely distributed sealsa new sample - flash printing. From the usual stamp they differ in that their working surface, which the impression is applied, is absolutely smooth. In this printing, several colors are used, it is more accurately and uniformly applied to the paper. Flash printing is much more durable, and the level of protection they have an order of magnitude higher.
Despite the durability and durability,After some time, the question arises as to how to fill the seal with ink. In order to quickly fill up flash printing in a simple way, you need to have a syringe and a suitable ink on hand. The cliché is located on the cushion pad. Remove the cliche and put it on a flat surface. Paint evenly several times with a syringe. Between applications, you should wait for a while, so that the ink is evenly absorbed in the cliche. The layer of applied liquid should not exceed 2 mm. We let the paint absorb completely, wipe off the excess of the applied ink with a napkin and collect the seal in its original state.
When refilling multicolor flash printing, you needget the cliché as described above. This part is filled with syringes, and care should be taken to ensure that the colors do not mix. Paints of different colors have different degrees of fluidity. Remember how to fill the seal with ink, it's easy: first, paint is applied to one print segment, then to another. When refueling for each color you need to use a separate syringe, otherwise the colors will be dirty and blurry. After the procedure for filling the ink with a cliche, the flash print should be put aside. The paint should evenly spread over the surface, this takes some time. After that, we paste the cliché into place and try fingerprints.
