Furnaces to work out a drip type do it yourselfquite often make masters and home craftsmen. These units act as a great way of autonomous heating. If there is a desire to use equipment that is one of the cheapest to operate, then it is worth making such a furnace. Used as a fuel can be used oil, which can be engine or transmission.
To make such a design is capable of anymaster, due to the simplicity of the work, during which there will be no need to use a special set of tools and materials.
Furnaces to work out a drip type do it yourselfare made on the basis of two combustion chambers, which implies the combustion of fuel twice during the operation of the structure. In the first chamber of this type of installation, the process of burning waste oil is carried out, which is accompanied by the release of a significant amount of combustible vapor. As soon as these vapors arise, they enter the second compartment, in which the mixing of oxygen and combustible gases takes place. The resulting mixture begins to burn in the second chamber, which is accompanied by the influence of a considerable temperature and the release of a large amount of heat.
In the manufacture of the furnace for the development of dripType your own hands you need to choose the right place to install it. Due to the fact that the work of the structure is accompanied by the burning of fuel at rather high temperatures, it is necessary to take care of safety rules that do not involve the installation of the structure in a place that is blown through.
Чтобы установка работала нормально, необходимо provide oxygen to both combustion chambers. Excess air should not be supplied to the first compartment, and in order to regulate its flow, a damper should be installed. The second chamber should receive enough oxygen. To do this, in the pipe that matches the two compartments, many holes should be drilled, each diameter should be approximately equal to 10 mm.
In the manufacture of the furnace for the development of driptype with your own hands you need to remember that it can be supplemented with some elements. This will allow the construction to be used for heating several rooms at once. Such a functional oven will have if you connect it to the heating system. Initially, it is necessary to install a tank for heating the water that needs to be connected to the system, only after that the return line is connected. Thus, the installation will not only be able to heat the rooms, but will also allow water to be heated, as well as to cook food. The design of this type has many advantages, one of which is expressed in small dimensions, allowing you to dismantle the furnace in a short time, and then install it in another place. Be sure to supply self-made furnaces for testing drip type with your own hands with a chimney, the height of which should not be less than 4 m. Make sure that the chimney is free from horizontal sections. In order to be able to clean the pipe, which will have to be done once a week, you need to provide the element with a system that allows dismantling.
In the manufacture of the furnace to work out their own hands,The drawings of which are presented later in the article, you must initially think about what design it will become. Thus, the basis of the design may be steel or gas cylinder. Before manufacturing it is worthwhile to estimate that it is rather difficult to implement drip feed by yourself. If the burner is insensitive to impurities that may be contained in the waste oil, the drip mechanism, on the contrary, is extremely sensitive. In order to reduce sensitivity, a filter should be put on the hose, it is permissible to use the one used in cars.
The pump can also be borrowed fromcar, you can apply a high pressure fuel pump. Due to the fact that it will give a significant pressure, it is necessary to do the return flow, so that the excess amount of oil will flow back into the tank. In the role of a dropper, you can apply medical. It has a clamp, it will allow you to adjust the flow rate.
If you decide to start making a stove onworking out your own hands, preliminary drawings should be considered and prepared by the one on which the work will be conducted. To carry out the process, the master must initially prepare some materials and tools:
The most suitable option for makingIt is considered a gas cylinder, which has thick walls. But if you use sheet steel, firstly, you have to look for one that has a sufficient thickness, and secondly, it will be necessary to produce an impressive amount of welding, which will make the manufacture more laborious. Do not forget that the first chamber will begin to work normally, if it contains a damper necessary for adjusting the oxygen supply - only this way the furnaces are made for working out with their own hands. Drawings (it is easier to calculate the gas from the gas cylinder) should be prepared in advance and select the one that will be most convenient to work on.
Be sure to remember that the camera whereburning oil is carried out, it is necessary to do this so that during operation it is possible to disassemble it, only this way it will be possible to facilitate the cleaning. Horizontal sections of the chimney are not needed, since they can be degraded, and in addition, there should be a minimum amount of sloping ones. It is preferable to make the pipe vertical.
In the manufacture of the furnace to work out their own handsdrawings (from a gas cylinder) will allow you to do the work correctly. So, initially the balloon is to be prepared, only after it is possible to start cutting off the top and the bottom part from it. In order to install the furnace and make it stable, legs must be welded to its lower part, which are prepared from the cut parts. Then you can begin to manufacture the combustion chamber, which should be collapsible. In this compartment a hole is made into which the tube is installed; through it, the flow of fuel and oxygen will be regulated.
In the center you need to weld the pipe in advance.made holes. This element will connect two compartments, in each of which combustion takes place. The second compartment can be made from the middle part of the product and steel sheet. After the camera is ready, it has to be strengthened by using a welding machine to the pipe from above. After the chimney is made and installed.
After the manufacture of the furnace to work out theirhands, the photo of which is presented in the article, it is necessary to check for functionality. However, you should not immediately fill the entire compartment with oil, as well as throughout the entire life cycle, this will prevent the oil from splashing out of the combustion chamber. It is necessary to fill it only on 2/3 volume.
Если вы решили заняться изготовлением печи на working out a drip type with your own hands, the drawings will definitely come in handy. It is important to know how to work with the balloon, otherwise an explosion can be avoided, because even if the product has not been used for a long time, there may be gas in it that is dangerous. Initially, the valve should be removed from the cylinder by the screwing method, after which the cylinder should be freed from residual gas. Then water is poured into the hole, only after that you can start working with the grinder, which will allow you to rid the product of the upper part with the hemisphere. At the next stage, the master will have to separate the same area from the bottom of the product. You should not start cutting the balloon if you haven’t completed all the steps above.
In the manufacture of the furnace for the development of dripType your own hands from a gas cylinder, you must get two hemispheres, which must be welded by the method of forming an annular seam, this will allow to form the first compartment. In this case, the lower section with the stand should be left below. To the top, which also has the shape of a hemisphere, over the hole should be welded pipe, which has perforations. Through this channel, gases will rise to the second compartment, mixing in parallel with the air. This indicates the need for a rather thick perforation.
After the lower chamber has been prepared andThe adapter is mounted in the form of a pipe; you can start manufacturing the upper chamber. Its assembly is made from the middle part of the product, but before that it is necessary to block the ends of the cylinder using sheet steel. In this case, the master must prepare in the bottom “cover” an entrance for installing a perforated pipe, and at the top - an opening for mounting a chimney pipe.
Kilns for testing drip type veryeconomical, and you don’t even have to buy fuel for them, especially if you are a motorist. That is why for heating a garage or industrial premises such equipment acts as the best.
