When finishing floors, sometimes there is a needcreate a durable and reliable coating that will perfectly undergo mechanical impact and friction force. The surface must be able to withstand moisture, have a minimum coefficient of expansion and carry the influence of chemicals. It is for this purpose that the rubber floor is used.
Pretty modern and comfortable design option.The floor is a rubberized coating. However, for a start it is important to determine which type of material to choose. Among others, there should be highlighted the roll material, which is based on a thin layer that can protect from cold and noise. This coating has notches that increase friction. This indicates that the surface is able to resist slipping even at high humidity.
The second type is individual modules,which are made of thick rubber. They look like tiles and are represented by original puzzles. In addition to the usual characteristics discussed above, such modules have specific qualities, for example, they are able to undergo high loads and strong mechanical effects. This coating can withstand acids and active media.
Before laying the rubber flooring,you have to prepare the surface. From the professionalism and thoroughness of this stage depends on the evenness and quality of the resulting sex. The main requirement for the base is the absence of large differences in height. Cracks and potholes on the surface should not be. The basis may be the following types of grounds:
Preparation involves alignment toheight, puttying, dust removal and priming. In the case of laying a rubber roll coating in an open area, it is necessary to ensure a natural slope. You can add coverage to the drainage system, which provides for the presence of gutters and slopes. In this case, even after rain, the rubber surface will remain dry.
If you decide to lay a rubber floor, then forFirst you need to prepare the surface. For this, a leveling mixture is usually used, which will achieve an excellent result. On the surface at the next stage, a thin layer of glue is applied, only then can we proceed to rolling the material.
If you decide to use modules, it’s betterapply the composition to their back surface. For roll rubber, a dense roller is used, with which you can remove excess air from under the coating. They try to perform such surfaces seamlessly, however, if necessary, they can be repaired with a special composition of crude rubber and fixed with a heater. Usually a vulcanizer or soldering iron is used for this.
It’s better to spread the rubber floorwith the help of another person. This recommendation is due to the fact that one roll of material usually weighs approximately 120 kg. Joints can also be glued with double-sided tape, which will increase the strength of the coating.
After the roll is rolled, it is necessarytrim it around the edges, guided by the size of the room. To do this, use chalk, a measuring device, a rule and a paint knife. It is worth noting that the rubber floor is laid using double-sided tape, if you do not plan to mount the coating on an adhesive basis. This approach has its advantages, which are expressed in the fact that, if necessary, the material can be reused in other areas. In addition, this technique is used for temporary flooring.
The surface must be solidsmooth and dry. If concrete is used as a rough foundation, then it is necessary to maintain it after pouring within 28 days. The material can also be laid on a wooden base, which must be dry. Its humidity should not be higher than 10%.
It’s important to make sure that the base is uniform,it is cleared of old paint and has an even relief. In the case of a wooden base, it is only possible to lay the rubber floor covering on a solid surface. As soon as it was possible to measure the rubber and mark the places of its cutting, it is necessary to roll the roll back.
When dealing with wood flooring, you have tosanded and primed. Moisture must not get on glued surfaces. The quality of work depends on the choice of glue. The surface can be operated after 24 hours. Using this technology, it is possible to arrange roll coatings with any thickness.
If you do the work yourself, you don’tplanning, you may be interested in the price of a rubber floor. Installation work will cost 400 rubles. per square meter. In this case, we are talking about stables, stadiums, gyms, etc. But if it is necessary to carry out work on laying treadmills from the described type of coating, then such work will cost 1250 rubles. per square meter.
Если вы выбрали резиновые полы для гаража и If you plan to do their laying yourself, then after preparing the surface you need to roll the roll along the wall and leave it to rest for 12 hours. Material cutting should be carried out with an allowance. It should be placed on the wall by 15 cm. This is necessary to reduce the defects of the room due to the curvature of the walls.
According to this technique, cutting allrolls. The canvases should fit close to each other. Before laying a rolled rubber coating, you should take care of the presence of some tools, including a construction knife and a metal ruler. As soon as the canvas is laid on the floor after applying the adhesive, you can cut off the left-over allowances. This stage must be performed in several approaches.
Используя для укладки резинового покрытия two-component glue, you must take care of the availability of a special container for its preparation. To draw glue you will need a rectangular spatula. But you have to apply the mixture to the surface with a notched trowel.
