Довольно эффективным способом выравнивания The ceiling and wall is the use of drywall. With it, you can form a multi-level embossed designs with fancy shapes. However, the alignment of the surface - this is only the first stage of finishing work. The base is still to be painted.
Этот способ является одним из самых простых solutions for upgrading drywall. At first glance it may seem that staining is a fairly simple task. However, the surface of the sheets still need to get rid of minor flaws, as well as work on the preparation of paintings. If you want to use paint that will be mixed with color schemes, then you will need to still make a color test.
Quite often plasterboard walls and ceilingspainted with different colors, in this case it will be necessary to mark the contours. Each separate section of the ceiling or wall will have to be painted in several layers. As practice shows, the most difficult is the stage of preparation. Even if there are no special requirements for the quality of work, you will have to try, because the appearance of the surface depends on how well the foundation is prepared. After applying the first coat of paint will have to wait a certain time. It is usually indicated in the instructions and can last from 4 hours to a day.
If you will be painting,drywall must first be putty. This stage is obligatory, because when installing the canvases, seams are formed, which should be sealed, otherwise they will be visible. On the surface there may be gouges and dents, which often remain from fasteners. Before finishing the drywall, its surface must be wiped with a damp cloth to remove debris and dust.
The base should dry well, because the applicationMixture on a wet surface is unacceptable. The second step will be treatment with a primer, for this you can use a spray or a brush. It is important to exclude even the slightest drafts. The drywall canvases are then left to dry.
Quite often today painting is used,drywall can also be refined in this way. Putty on its surface is applied with a rubber trowel. The seams should be reinforced serpyanka. It is important to close up and deepening, which remained from fasteners. Putty should be applied to the joints, which should not be visible at the time of staining. Once everything is dry, you can grout using a mesh or sandpaper.
Many beginner home masters are setthe question of how to putty drywall for painting. This is discussed in the article, but it is also important to understand why this stage of preparation. Even if the canvases are quite even, then you should not give up the putty. This will reduce paint consumption. In addition, you can hide the green shade of the surface.
Even if you apply paint in several layers,achieve a good result will not work. The only exception is the case when the color of the paint coincides with the shade of the material itself. How to putty drywall for painting, you will learn if you read the material. One should not neglect the necessity of this stage, because otherwise the joints between the canvases will have to be filled with expensive paint, which in this case has to be applied in the number of layers equal to four. Choosing a high-quality paint, you will pay more than when you buy a putty, with the help of which the surface of the drywall is prepared.
Quite popular today is painting, drywall,after you have installed it on the ceiling, walls or floor, must also be trimmed. Alkyd enamel may be suitable for this, which after drying forms a glossy surface. In this case, the available errors, defects and omissions may remain visible. Therefore, when performing work for beginners, it is recommended to choose water-based emulsion. On sale it is presented in different versions.
A water emulsion makes plasterboard dull, to itscolor can be added to the composition to achieve the desired shade. However, it is better to refuse this mixture if you plan to paint walls whose operating conditions are characterized by high humidity.
Если вами будет осуществляться покраска, drywall after the completion of such work should look attractive. Therefore, you should consider the purpose of the room. The water emulsion described above is suitable for almost any residential area. For kitchen and bathroom it is better to prefer water-based mixtures, which are designed for conditions with high humidity.
Acrylic is also quite popular today.water based paint. With its help you can achieve a matte or glossy surface. As a result, it will be possible to form a layer that is resistant to moisture. This option is ideal for bathrooms. Depending on the method of application, the paint will have a certain consumption. If you want to achieve high productivity, it is best to use a roller. From its foam varieties should be abandoned. Additionally, you should prepare a brush, with its help you will be able to paint inaccessible places.
Painting the plasterboard ceiling canprovide for applying the composition with different shades on one surface. To do this, separate areas are separated using a pencil or chalk. To determine the contour should be used masking tape. As soon as it is possible to paint one area, and it is completely dry, you can pull the tape over the edge and tear it off, starting to paint the rest of the ceiling or walls.
If you have prepared a plasterboard ceiling underpainting, it is important to stock up on some tools. Among others should be highlighted brush. With its help, the perimeter of the site is painted on which the rest is to be applied before the composition To do this, use a flat brush with a width ranging from 60 to 80 mm.
Paint can be poured into the paint bath, whichallows you to conveniently roll in the roller. With it, you can paint the rest of the area. The roller is dipped into the paint, and then using the stand, the composition will need to be distributed over its surface. At drawing each layer it is necessary to roll the roller in one direction. Along one lane should be held several times to paint evenly distributed.
Большая поверхность должна окрашиваться полосами, which will be located perpendicular to the direction of movement of the roller. Their width can vary from 60 to 80 cm. Once the paint has been rolled out from the roller, you should use the tool in the newly painted area. You should not touch the roller to the place where the paint has already begun to set. This will happen 5 minutes after applying the mixture.
Each next layer should be directedperpendicular to the previous one. It should be started only after the mixture is completely dry. Painting walls from drywall can be accompanied by certain difficulties. For example, you may have noticed that some areas were painted with excess composition. Do not remove the mixture at a time when the paint is already slightly dried. To cope with the task will be possible only after its full seizure. Excess can be removed with sandpaper, and then paint the area again. The process of applying gloss paint is more complicated. The appearance of noticeable stripes and divorces can be avoided only if you have certain skills in carrying out such work.
Технология нанесения водоэмульсионки несколько different from the one described above. Each subsequent layer can be applied in composition, which is still wet. In total, there should be two or three layers. If you have to work with the ceiling, then you can apply paint in two layers, the first of which should be located across the room, the second - along. When it is planned to apply the third layer, it should be directed along the premises, while the second - across. Dealing with the sequence is very simple: the last layer should be applied along the room.
If you are painting drywallwith your own hands, you can use enamel. However, the technique is somewhat more complex. The process will stretch, because you have to wait until each coat of paint dries, and such a composition will cost more compared to water-based mixtures.
The material is applied zigzag orchaotic lines. Until it has not dried, the composition is shaded using a brush. The second layer is applied along the room with stripes that overlap each other with an overlap. Two layers are usually enough to achieve a good result.
Начинать окрашивание необходимо от углов, не it matters what they are - wall or ceiling. To do this, you can purchase a corner roller. The places where the switches and sockets will be installed should be painted with a brush, retreating 3 cm. Instrument movements should be directed from the ceiling to the floor.
Before starting the process the paint should be wellstir If we are talking about the water-based composition, it is diluted with water, whereas in this case solvents are used for enamels. Drywall primer before painting, it is recommended to use an acrylic composition. The first painted joints between the canvases. Once these areas dry, you can begin to paint the entire surface.
Quite often for leveling walls todayused drywall. Painting, plastering of this material is necessary if you want to make the ceiling, walls and floor aesthetically attractive. However, it is important not only to choose the right paint, but also to use the method of preparation. For example, it will be necessary to apply a putty to the surface, which allows you to get rid of the errors that appear during the careless loading process.
As a result, sheets can be covered with dents andscratches, and their corners are knocked down. All these errors can be hidden using ordinary putty. Finishing drywall for painting is still needed, even if the transportation was carried out very carefully. After all, the sheets of material are installed with the help of screws - the places from the caps will need to be filled.
