The main convenience of automatic swing gatesis that you can close or open them through the remote control. Every person today wants to make his life as comfortable as possible. That is why the owners of private houses or their own garages are increasingly found automation for swing gates. The hands can be mounted pretty quickly, while getting an excellent result.
It's worth figuring out how this whole thing works.system. Gate automation is possible through a drive that is mounted directly on the gate. Automatic set for the gate is not difficult to mount with your own hands. The installation process can not be called so simple. Here it is required to observe a clear sequence of actions in combination of accuracy and qualification at each stage of work. When installing the drive has several features. It is necessary to consider the sash in relation to the height of the pillars. If the installed automation does not assume the presence of limit switches, then you need to install sash stops. If you miss such an important nuance, you can get a completely unexpected result. The motor will fail, and the functioning of the whole structure will be difficult to call normal.
The set of elements contains suchcomplex, as automation for swing gates. It will be possible to mount it by hand only if all the components are present. For proper and high-quality installation of the gate is required to understand this and have minimal experience in solving such issues. The automation kit contains: 1 control unit, 2 drives, 1 set of photocells, a small beacon and a remote control. The advantages of this type of mechanism include a long service life and exceptional strength. The mechanism is easy to operate, and the gate opens at a speed of up to 15 seconds. Among the shortcomings can be identified such a moment as the presence on the path of movement of the gate at least one barrier, because of which the drive may well fail, and this leads to jamming. There should be no obstacles in front of the opening. Only in this case, you can expect that the automation for swing gates will function with your hands for a long time, without failing. Conducting preventive measures will eliminate failures during operation of the equipment. All parts that require it must be periodically lubricated with special substances. When automation fails, it is categorically forbidden to exert physical efforts if necessary to open the gate, there’s only one solution - to call the master.
As you can understand, with a great desiredo-it-yourself automation for swing gates is no longer such an unrealistic idea. This is a pretty good way to save your own money. If you have not only practical interest in this case, but you are interested in the realization of the idea itself, then this is the case for you. And this is quite an exciting process.
As the main element of such a driveThe satellite antenna mechanism is used. Its equipment includes a worm gear, replacing the drive. The basis of the satellite television system consists of a turning mechanism. This is an engine that can be used to install automation. The worm gear works according to a principle similar to that of an electric drive. This option is more advantageous in comparison with store drives, since its operation requires a voltage of 36 volts, and for the store drives, the usual mains voltage of 220 volts. For assembly, you need to get two working drives from satellite dishes. It is worth choosing the models having the longest stock. It will take more remote and transformer, its power should be 36-40 watts. The remote control is used to open the structure and close it. It should work at a distance of about 50 meters. In addition, it would not hurt to stock up on two trinkets, sold in stores that sell goods needed in the field of protection.
To collect the drive will be quite enough 6 hours.In order for the gate automatics to function efficiently, it is required to equip it with a current relay. If it is not available, the motor may overheat and break. And with it, you can easily make a drive for the gate with the most minimal cash investment. If you like the finished assembly, you can save on installation.
When installing an electric drive for swing gatesIt is required to take into account the direction of the opening of the gate leaves: out or inwards So, if you are interested in how to install automation for the gate with your own hands, then you need to list the necessary tools for this purpose. You will need: drill, hammer, pliers, construction meter, screwdriver, insulating tape. In the automatic gate, unlike the usual, there is an electric drive. Therefore, before installing it, you need to decide which option to choose.
Electric drives can be linear or lever.To accurately determine the choice, you need to know the distance between the loop and the inner side of the pillar. At a distance of 1.5 cm, a linear actuator is required. Its cost is noticeably lower than that of the lever. If the measured distance is 1.5-3 cm, then it is appropriate to install a lever-type drive. It is as reliable as linear.
Схема автоматики ворот предполагает, что It is required to install not only a drive, but also a set of equipment. It is important to determine the width of the sash, as well as possible wind oscillations. Many people are afraid to install all this equipment on their own, as they do not have the proper experience and knowledge. But here it is important to remember the need for attention to detail, then there will be no problems with the installation.
It is important to check that the movement of the valves iseasy when the drive starts. If something interferes with this, then you need to find the cause and eliminate it, since the movement of the electric drive must be level. Otherwise, it is possible that the pillar may lean, the angle of movement will shift, and this has a bad effect on the automation of the whole structure. After eliminating a variety of problems, you can proceed to the automation installation process. It is important to follow the instructions as closely as possible so that the operation of the system is as long as possible.
Автоматика для распашных ворот своими руками installed on products that open inward, while it is appropriate to use any electric drive. When used as a base of steel pillars, it is appropriate to install a linear actuator. It is compact and reliable, and its cost is relatively low. You can use a lever drive, but it is much more expensive. Difficult option in the presence of brick columns and the gate is located right in the middle. In this case, the linear actuator is not suitable.
The lever-type automatics are mounted on a pole, while the gate is opened at the expense of levers, while they should be located no more than 200 mm from the posts.
In this case, two are available for use.kind of devices, but the right choice would be automatic for garage doors with a linear mechanism. This is a cheaper and high-quality solution. Automatic equipment is mounted in the opening, and takes no more than 150 mm on both sides. On narrow gates, the system is mounted at the top. The drive is usually mounted directly on the pole. Automation for swing gates with their own hands is set so that the hydraulic drive allows you to open them to the outside. Next, the bracket is welded to the construction. When opening a gate with a linear drive should be 1 cm free running. After that, you can check the correctness of the stroke of the valves and movement of electric drives. The next step is to install the stops for opening and closing, and then attach the engines. At the end, you need to equip the jumpers, connect to the consoles, as well as turn on the mechanism. If one leaf has to move in a different direction, then it is required to swap the wires on the engine.
After that, automation for swing gateshands must be equipped with limit switches. If you have not foreseen the use of such elements, then it is required on the board to set the life of the sash, as well as the force of opening and closing. You should not set the maximum effort, as this will reduce the service life of the device. It is recommended to set the minimum effort to ensure that the gate opens outward normally.
Next, you need to build a warning lamp, as well as a special photo device. Gates that open to the outside, will work quite well with such automation.
Quite often there are cases when peopleassemble everything with their own hands, but do not cope with this task due to lack of experience. This leads to a lot of errors, due to which the automation refuses to work, and the drive completely fails. Everything should be connected in stages, as this will allow to correct any problems in case of mistakes. Otherwise it will be very difficult to establish the cause of the breakdown. Correct and accurate installation together with the high quality of the electric drive allows the gate to function as long as possible and correctly. Even if you use automatic for sliding gates, you will quickly be able to assess how comfortable it has become for you to call in. This is especially noticeable in the winter when you do not want to leave the warm interior of your car to open the cold gates.
To protect the entry zone in the territory of differentDestinations can be used sliding gates that operate using special automation. In this case, there are also certain features of installation. Automation for sliding gates with their own hands is set in stages. First you need to weld a steel cantilever pipe to their structure. During the operation of the entire structure, it moves along roller carriages installed on a specially organized foundation. Well established itself for the gate Came. In the closed position, the lower corner of the door is rolled by an end roller into the trap. During the opening of the canvas such a movement helps to prevent lateral oscillations of the device.
Automation for sliding gates should be mounted taking into account certain points:
- the installation of such structures begins with the arrangement of an independent foundation, as well as the foundation, located in the opening and on the side of it, in the direction of the opening of the entire structure;
- fastenings of gate and their framework should be characterized by a high degree of resistance to the effects of winds;
- installation of a special holding part is required, by means of which it is possible to increase the width of the web structure in the direction in which the gate opens;
- the system of sliding gates should be provided with effective protection against burglary, as well as a special type of protection against various adverse factors.
Now you know how automation is mounted.swing gates do it yourself. If you have a strong desire, you must strictly follow the instructions in order to get the desired result. It is important to note that the automation for sectional doors is established according to a similar principle. Therefore, you should not have any difficulties with the installation process.
