There is no person who would everLife is not faced with the need for repair. Some prefer to accumulate a certain amount of funds and entrust the execution of works to specialists. Others, on the contrary, wish to do all the work themselves. In this case, it will be useful to get acquainted with the technology of performing some works, then to apply knowledge in practice.
Today we will talk about an important component of any repair - the installation of ceiling plinth.
The most difficult to perform this type of workis the design of the corner. Here you need to accurately and accurately dock slats, because the appearance of the decor may suffer. You do not know how to dock the ceiling plinth in the corners? Not confident in your abilities? Then you can use ready-made blanks that are set in the corners.
Но соединенные вместе потолочные элементы look more harmonious. Yes, and on special corner elements you can save extra money. So, how to dock the ceiling plinth in the corners correctly, how to handle the seam?
Ceiling plinth - one of the most important decorativeitems. It allows you to hide various errors of repair. They fix it after the wallpaper is stuck in the room. Ceiling baseboards are located at the junction of the ceiling and walls.
You should seriously consider choosing a plinth. The correct model and size of the ceiling plinth can visually increase the space. Now consider, tohow to connect the ceiling plinth in the corners correctly.
Modern manufacturers offer a wide range of ceiling plinths. They are made of plastic, foam, wood, polyurethane foam, gypsum.
Wooden plinths look more aristocratic, but working with them is quite difficult. The same goes for gypsum.
By the way, ceiling plinths are also called baguettes and friezes.
For pruning may need differenttools that can be found in every home. Using a knife or scissors you can easily cut the polystyrene strips. The hacksaw is used for trimming wooden skirting. A hacksaw is useful for trimming a plastic baguette.
Stouslo is a special tool thatused for the most accurate trim baguettes. This is a special tray, which consists of 3 interconnected boards. They have special slots. Each of them is located at a certain angle relative to the axis (45, 60 and 90 degrees). They are designed to correctly guide the blade when cutting.
Stuffers can be purchased at the hardware store. It can be useful not only for trimming ceiling plinth, but also in the future for other types of work.
It is necessary to fit the ceiling in order to correctly and beautifully join the ceiling plinth in the corners. Consider how to properly perform this procedure.
The right lane of the ceiling plinth should be placed in the tray in the left side of the wrong side to the bottom. In the future, this part will be in contact with the ceiling.
The bar should be pressed tightly to the tool and carefully cut it through the slot.
Then, in the tray from right to left, insert the second ceiling plate. Carefully cut it off.
Finished planks are attached to each other andadjust the knife junction. Doubt how to connect the ceiling plinth in the corners correctly? There is a sure way. When making the interior corner, the edge adjacent to the wall should be longer than that adjacent to the ceiling. When finishing the outer corner - on the contrary.
Как состыковать потолочный плинтус в углах?This procedure can be performed independently, rising to the ceiling of the room on a stepladder. But it is inconvenient. Therefore, many experts recommend immediately glue polyurethane and foam elements on the floor with a special glue. It is quite simple and effective.
What to do if there is no stusla at hand? It is very easy to adjust the slats without the use of special tools. There are 2 ways to solve this problem quickly:
If there is no special tool at hand, then how to cut a corner on the ceiling plinth? It's simple, because this device can be built independently.
Making the craft with your own hands:
Самодельное стусло готово.It is enough to attach the right-hand ceiling element on the right side with the lower edge to the line nearest to you and cut along the line. The same should be done on the left side, putting it on the left side.
In the second case, the procedure is as follows:
This method allows you to carefully cut the corner on the ceiling plinth.
Now we find out how to properly connect the slats.
Remember that ceiling plinth pvc can be cuta knife. But before it should be well sharpened. Otherwise, the edge of the baguette will crumble. For such purposes, a special construction knife is often used.
In Soviet homes, the walls are often not even, respectively, and the corners. We learn how to act in this case, because the case here will not help.
Install ceiling PVC plinth is easy.You just need to correctly measure the angle. Often for this purpose use a special tool - the protractor. If not, you can make a pattern of paper, and then use the protractor. You can cut out the necessary future internal or external angle using a self-made pattern.
В некоторых комнатах есть внешние углы.They are quite common, so you need to know how to make a corner. Ceiling plinth of foam is most often used for finishing apartments. It's easy to work with him.
In order to properly cut the baguette, it is necessary to correctly draw marks on it. To do this, attach the element to the ceiling and mark on the baguette the place of the cut.
After that, the element is laid in the wort and cut at an angle of 450. How to make a corner?The ceiling plinth from polyfoam for an external corner is made in the same way, as for internal. If a large part of the element is located on the left side, it is necessary to cut it off by the left designation. The second element is also made on the same principle.
By trimming the elements, you should make sure thatThere are no errors. How to adjust the angle of the ceiling plinth? You just need to attach both parts and determine whether they ideally fit together?
How to make a corner on the ceiling plinth, we already know. Now we will consider how to finish finishing the joints and what to use for their putty.
Often between the two elements are cracks. They are sealed with putty or silicone sealant. Filling in the future often paint over the color of the plinth.
Outside corners should be more carefully customized. Then even a small gap will be almost impossible to remove. Especially, if the wide plinth was used.
If you do not know how to make a corner onceiling plinth, you can use ready-made corner elements. They come in different sizes. Often, designers use ready-made corner elements of a larger size than the entire baguette around the perimeter. In this case, the corners of the room stand out in particular. Trim ceiling strips to connect with these elements should also occur using the miter box. If this device is absent, the baguette can be independently cut. Cutting should take place at right angles.
Install finished parts on liquid nails.or glue. Apply adhesive to the back side of the material. Please note that the glue is in those places that are in contact with the ceiling and wall.
How to connect the ceiling plinth in the corners?Yes, just like the rest. Glued bar should be applied to a specific place between the wall and the ceiling. Then, not too hard, gently press the element to the wall surface. Experts recommend performing this procedure with the edge of the palm. This method must be recommended to use for baseboards made of foam. Indeed, on the surface of this material quickly dents are formed.
Помните, что во время того, как соединяют ceiling plinth in the corners, glue may appear on the edges. Remove it immediately with a cloth or clean rag. All parts can be fixed with masking tape for a while, until the glue dries.
After the glue is dry, paper tape must be carefully removed. The gaps at the joints between the slats fill with sealant or putty. If necessary, the plinth can be painted in any color.
In fact, for many who did not know how to glue the ceiling plinth in the corner, it would seem that in this article everything is described too simply. But it really is.
The process of mounting the ceiling plinth onThe inner and outer corners are pretty simple. A person who does not have certain skills in performing construction work can cope with this. But at the cutting stage there may be some difficulties, because the process requires great precision. If the cutting is performed poorly, the whole structure will be incorrectly sorted. In this case, the slats will not fit snugly, and gaps will form at the junctions.
Many experts recommend to start to get an additional meter of material to practice properly cut corners before starting work.
