Homemade for motoblock can be excellentassistants in the household. The most common for this equipment are trailers. They can be useful for transporting harvested crops, seedlings, tools, and garbage.
If you make homemade products formotoblock, then you can do a trailer. The simplest model is made using steel pipe, wheels, springs, duralumin sheet, sheet steel, fasteners, electrical tools and channel bars. As for the pipes, their cross section should be 25 x 25 and 60 x 30 mm. Among electric tools it is possible to distinguish a screwdriver, electric jigsaw, welding machine and a Bulgarian.
Homemade for motoblock can assumeexecution of the trailer, it will be based on a frame, which is a single structure. It will be placed on a wireframe. For the arrangement, two traverses must be made, which are made from a corner with a side of 25 millimeters. These elements act as rear and front crossbars. All workpieces can be joined by means of five cross-pieces in such a way that eventually it has turned out to form a lattice. To the longitudinal pipes, by means of welding, the posts are fixed, to the upper part of which, with the help of a welding apparatus, it is necessary to strengthen the straps from the corner. The trailer can be equipped with folding sides, for this purpose the frame should be made separately from the frame. The grating of the platform must be covered with a sheet of duralumin, which is fixed with bolts. To ensure that the fasteners are the most durable, you should use a welding machine.
When homemade crafts are made, inparticular trailer, you need to insert each other two channels, which have the same length. At the same time one of the ends is supplemented with wheel axles. The beam is connected with spars by means of a spring. The ends of the springs should be put on the axis of the bracket, and the central part should be welded to the beam. The borehole must be made using rectangular pipes, the cross section of which is 60 x 30 millimeters. In order to obtain a double-beam structure, it is important to dock the front ends of the pipes, and then weld to the hitch housing. On this we can assume that the trailer is ready, if necessary, it can be equipped with headlights, stop lamps and turn signals.
Homemade with a motor from a motoblock can becomeno less useful assistants on the plot. To do this, prepare metal, wheelset, bearings, seats, hardware, lubricants, as well as paint or primer for painting the product. Metal rolling will be the basis of the welded frame. It is important to choose a seat to fit the dimensions. During the assembly, you will need bolts, nuts and studs. As consumables, there will be electrodes, oxygen, wire and gas.
When making homemade cross-country vehicles frommotoblock, the masters use a welding machine, a metalwork tool, namely a hammer and a chisel. If necessary, you need to stock up with a set for gas cutting. The angle grinder is required for grinding and cutting of metal blanks. It is important to take care of the presence of dies and taps. Every home craftsman probably has an electric drill, and a set of drills can be purchased at any store of the corresponding goods. It is important to prepare materials for dyeing and anti-corrosion protection of metal, which will extend the life of the product. When homemade products are made on the basis of a motor block, it often requires the use of turning equipment, which is required to manipulate the wheel pair.
It is important at the initial stage to take into account that the constructionmust have an equilibrium, otherwise loads can cause the device to collapse. The design will include a reverse gear, engine, rear and front axles, cardan gear and chains. The motor will cause the wheels that are located in the front to rotate. The torque is transmitted by means of a chain, then it goes to the propeller transmission and the rear axle. In the end, the rear wheels also rotate, which in this case will be leading.
If you decide to perform such homemade products frommotoblock, they are recommended to consider their photos even before the manipulations begin. Applying pipes and corners, at the initial stage it is necessary to make a frame. It is important at the same time to correctly locate the bushing and the fork, which will ensure the ability to turn the trailer. The body is most often made using steel sheet. However, do not make the side, the height of which will be more than 30 cm. The next step is to install the driver's seat, as well as attachments. It is important not to forget that before the operation, the structure must be analyzed for operability. The finished product must be painted.
After you have decided on the dimensionsdesign, you can calculate the number of meters of metal. It is also important to determine the number of channels that will perform the function of the frame for the hitch. In order to produce the most functional trailer, it is recommended to use a welding machine, refusing self-tapping. In the first case, it will be possible to produce a structure that will last long enough. To make the frame, you should prepare the corners, the cross section of which is equal to 50 x 25 millimeters, and also 40 x 40 millimeters. You will also need trimming pipes of round and rectangular cross-section. The body will be made of boards, the thickness of which is 20 millimeters. Stock up and a square bar with a side of 50 millimeters, it will form the basis of the supporting beams.
As the most functional homemadeDiesel motoblock is exactly the trailer. In this example, a construction is considered that consists of 4 nodes, namely: body, frame, carrier and wheels. All of them must be connected together by a welding method. The body will be made of wood, namely from 20-millimeter boards. The corners should be reinforced with steel corners. Mounting the frame to the body must be carried out by means of wooden beams in the amount of 3 pieces.
For the reason that this trailer isuniaxial design, load distribution must be ensured so that the center of gravity is shifted to the front. It is important to exclude the output of the center of gravity beyond the wheel axle. If there is a desire, the device can be further improved by the flip walls.
When carrying out the described self-made of motoblock"Cascade" it is necessary to use the wheels borrowed from the motor rifle FDD. In order to ensure the coincidence of the axle rod and the diameter of the bearing of the hub, it is necessary to sharpen the ends. The arrangement of the wheel axle will be accompanied by the use of a metal rod of 30 millimeters. Its length should be such that in assembled form the wheels are not outside the rim of the body. With the help of welding, you need to fix the rod through kerchiefs and supports to the body and spars.
To connect the trailer with the motor block itselfyou need to make a console. It is fixed to the attachment of the attachments, for this reason the upper part should repeat the shape of the rim holder. Only in this way will it be possible to create a reliable attachment for the trailer.
