Malfunction motoblock can be divided into twocategories: motor problems and problems with all other mechanisms and nodes. If in your arsenal there is a similar equipment, then in the process of operation, with the greatest probability, you may encounter engine problems.
The instruction for the repair of the motor block "Cascade"presented in the article, will allow you to understand what malfunctions could occur with the engine, as well as how to eliminate them. The motor may stop running if it can not be activated, then a spontaneous stop, a lack of power set and a fault may indicate problems.
If the device has a petrolthe engine, in the process of troubleshooting it is necessary to check whether there is fuel in the tank, what is the condition of the air damper of the carburetor, how the ignition is switched on, and whether the fuel is injected into the carburetor. To verify the last condition, it is necessary to fill the float chamber by using the corresponding button. In this case, the fuel should be poured out of the hole in the cover of the float chamber. If the gasoline runs in a thin stream or it is not at all noticeable, it may indicate a contamination of the fuel filter or the clogging of the air valve. The repair instruction for the Kaskad motoblock in this case involves cleaning the valve or filter.
The fact that fuel enters the engine cylinder,may indicate the condition of the candle. It is recommended to check it by unscrewing the cable from the cylinder cover. If the candle is dry, this indicates that the fuel mixture does not enter the cylinder. If you managed to establish that the fuel enters the carburetor, a possible cause of the engine failure from startup may be contamination of the carburetor filter grid.
Sometimes a malfunction leads to a malfunctionjets. If the above conditions are met, the repair instructions for the Kaskad motobloc provide for the removal of the carburetor, disassembly and cleaning of the element. These works can be made without visiting the service workshop.
A repair instruction for the Kaskad motoblock, whichyou must be studied before carrying out the work, will allow you to understand how to inspect the condition of the candle. If it is wet, the gasoline enters the cylinder. Failure to start can be the result of an excess of fuel mixture. If the surface of the candle is excessively covered with gasoline, it is necessary to dry the cylinders, pump the engine with a starter, leaving the candle in an inverted state. Before this, the master must shut off the fuel supply. The candle can be contaminated with carbon, while it is cleaned with a fine skins and gasoline. It is important to analyze the size of the gap between the electrodes. If required, it must be adjusted, following the requirements provided by the manufacturer in the manual. The size of the gap should be 0, 8 millimeters.
The ignition of the Kaskad motoblock can also come out ofbuilding. If this happens, you need to check the condition of the spark plug, clean it and adjust the clearance. In parallel with this, it is necessary to analyze whether there is damage in the electrical circuit. The master must check which gap is maintained between the magnetic core and the coil. Different models of the manufacturer mentioned recommendations for conducting these works are listed in the instructions.
The carburetor of the Kaskad motor-block can appearcontaminated, in some cases it may be incorrectly made adjustment. If this happens, this node is removed and cleaned, it is adjusted, which should be provided by the instruction.
There may be another problem thatexpressed in the fact that the air in the carburetor enters in insufficient volume. This can occur due to contamination of the air filter, eventually the fuel mixture is over-enriched. During operation, you must perform periodic cleaning of the air filter to eliminate the described trouble. However, if the equipment is used under excessively dusty conditions, more frequent cleaning may be required.
Вы должны проанализировать, в каком состоянии there is an air filter. Depending on the material in the base, you need to rid the element of dirt in one of the appropriate ways. If the carburettor of the Kaskad tiller begins to get air in insufficient quantities, then you may need to clean the paper filter, which is done by lightly tapping or blowing. If you have a foam filter, you can rinse it, and then dry it well. The strainer is vacuum cleaned. These elements have their own life, as soon as it is developed, the node must be changed.
Cascade tiller adjustment originallyproduced in factory conditions. But if you are faced with the need to adjust the carburetor, then this should be done according to the technology, which provides for the first stage to wrap the two screws all the way, without making much effort. Next, the screws turn away 1.4 turns, while the engine must be started and warmed up. The gas lever is set to a position that corresponds to the lowest possible speed. The master must establish a steady idle speed. The last operation must be repeated until you achieve uninterrupted engine idling.
Kaskad motor-block, maintenance instructionwhich will allow you to eliminate the need for premature repairs, may include an adjustment of the engine. At the same time, the corresponding screws are turned away or wrapped until stable operation is obtained.
Kaskad motor-block, maintenance instructionwhich will allow you to use the equipment with maximum efficiency, must be periodically serviced, this applies to cleaning, refueling and washing. When conducting these manipulations, the engine must be stopped. All adjustment work must be carried out with the engine stopped, this requirement does not apply to carburetor adjustment. Operation of the motor-block should be made with protective covers.
The characteristic of the Kaskad motor-block will allow youmake the right choice. This device is a universal mechanical tool that will be an effective assistant when working on the plot. If we are talking about small areas, then you can prefer light or medium tillers, whose weight does not exceed 120 kilograms. If you are faced with the task of cultivating the land with an area of hectares, then you will need an industrial heavy machinery.
The device has two rear or fronttransmission, and the speed is 8.3 and 3.7 kilometers per hour. If you want to choose a model for solving problems on the territory of your own site, then you can purchase a model with a mass of 103 kilograms. This tiller rather limited size: 83x48x74 centimeters.
